BENDIX VORAD VS-500 Gebruikershandleiding - Pagina 2
Blader online of download pdf Gebruikershandleiding voor {categorie_naam} BENDIX VORAD VS-500. BENDIX VORAD VS-500 12 pagina's. Ups package car drivers
Ook voor BENDIX VORAD VS-500: Gebruikershandleiding (16 pagina's)
Pagina afdrukken
Introduction
The Bendix
VORAD
™
adaptive cruise control system and Forward Collision Warning. This
Operator's Manual explains the features and functions, enabling maximum
performance from the system.
Read this manual thoroughly before operating the system. Be familiar
with the controls, system alerts, and what to expect when the system
is on. Keep this manual in the vehicle as a reference for the system, its
operation, and performance characteristics.
Additional Information About Bendix
For additional information about Bendix
Bendix Tech Team at techteam @ bendix.com or call 1-800-AIR-BRAKE
(1-800-247-2725). Visit www.bendix.com for more information and for
any updates to this document.
WARNING! PLEASE READ AND FOLLOW THESE INSTRUCTIONS
When working on or around a vehicle, the following guidelines should be observed AT ALL TIMES:
▲ Park the vehicle on a level surface, apply the
parking brakes and always block the wheels.
Always wear personal protection equipment.
▲ Stop the engine and remove the ignition key
when working under or around the vehicle.
When working in the engine compartment,
the engine should be shut off and the ignition
key should be removed. Where circumstances
require that the engine be in operation, EXTREME
CAUTION should be used to prevent personal
injury resulting from contact with moving,
rotating, leaking, heated or electrically-charged
components.
▲ Do not attempt to install, remove, disassemble
or assemble a component until you have read,
and thoroughly understand, the recommended
procedures. Use only the proper tools and
observe all precautions pertaining to use of those
tools.
▲ If the work is being performed on the vehicle's
air brake system, or any auxiliary pressurized air
systems, make certain to drain the air pressure
from all reservoirs before beginning ANY work
on the vehicle. If the vehicle is equipped with a
Bendix
AD-IS
air dryer system, a Bendix
®
®
dryer reservoir module, or a Bendix
dryer, be sure to drain the purge reservoir.
▲ F o l l o w i n g t h e v e h i c l e m a n u f a c t u r e r 's
recommended procedures, deactivate the
electrical system in a manner that safely removes
all electrical power from the vehicle.
▲ Never exceed manufacturer's recommended
pressures.
▲ You should consult the vehicle manufacturer's operating and service manuals, and any related literature,
in conjunction with the Guidelines above.
The trademarks used in this document, including Bendix
or licensed to Bendix Commercial Vehicle Systems LLC.
VS-500
system includes Bendix
®
™
GENERAL SAFETY GUIDELINES
TO AVOID PERSONAL INJURY OR DEATH:
DRM
®
™
AD-9si
air
®
®
2
Systems
®
systems, contact the
®
▲ Never connect or disconnect a hose or line
containing pressure; it may whip and/or cause
hazardous airborne dust and dirt particles. Wear
eye protection. Slowly open connections with
care, and verify that no pressure is present. Never
remove a component or plug unless you are
certain all system pressure has been depleted.
▲ Use only genuine Bendix
parts, components and kits. Replacement
hardware, tubing, hose, fi ttings, wiring, etc. must
be of equivalent size, type and strength as original
equipment and be designed specifi cally for such
applications and systems.
▲ Components with stripped threads or damaged
parts should be replaced rather than repaired.
Do not attempt repairs requiring machining or
welding unless specifi cally stated and approved
by the vehicle and component manufacturer.
▲ Prior to returning the vehicle to service, make
certain all components and systems are restored
to their proper operating condition.
▲ For vehicles with Automatic Traction Control
(ATC), the ATC function must be disabled (ATC
indicator lamp should be ON) prior to performing
any vehicle maintenance where one or more
wheels on a drive axle are lifted off the ground
and moving.
▲ The power MUST be temporarily disconnected
from the radar sensor whenever any tests USING
A DYNAMOMETER are conducted on a vehicle
equipped with a Bendix
, are United States trademarks owned by
®
SmartCruise
™
®
brand replacement
®
Wingman
system.
®
®