BENDIX EC-30 ABS-ATC CONTROLLER Installatie-instructies - Pagina 3
Blader online of download pdf Installatie-instructies voor {categorie_naam} BENDIX EC-30 ABS-ATC CONTROLLER. BENDIX EC-30 ABS-ATC CONTROLLER 3 pagina's. Service replacement kit
Ook voor BENDIX EC-30 ABS-ATC CONTROLLER: Problemen oplossen (2 pagina's)
Pagina afdrukken
System Check-out
With the brake system fully charged with air, fully apply the
service brakes and hold. Remove and apply ignition power.
Does each PMV (modulator) exhaust air in the following
pattern (SA Right, SA Left, DA Right, and DA Left)?
Does each PMV exhaust air once per pattern (not twice)?
Does the pattern of PMV exhausts repeat?
Did the ABS indicator lamp illuminate for a period of
approximately three seconds and then extinguish? (Assuming
no diagnostic trouble codes are present.)
Verify that only the green LED is illuminated. Any red LEDs
that are illuminated indicate a diagnostic trouble code.
With the power off, remove the 30 pin connector from the ECU.
Key vehicle on. Does the ABS indicator lamp illuminate?
Does the ABS indicator lamp illuminate as required when ABS
is disabled due to a fault in the system?
(Where an off-board diagnostic device is available for testing.)
Is the ECU communicating over the J1587 link? (The J1587
link may not be connected to the ABS ECU.)
Is the correct ECU installed? (Verify ECU part number)
Are all Wheel Speed Sensors (WSS) wired properly to the
ECU? (for example, SA Left WSS to SA Left WSS ECU input)
Open each wheel speed sensor connection, making sure the
correct component and location are displayed on the LEDs:
Steer Axle Right Sensor
Steer Axle Left Sensor
Drive Axle Right Sensor
Drive Axle Left Sensor
Do all WSS have acceptable signal output (0.25 VAC @ 0.5
RPS)?
Are all PMVs wired properly to the ECU? (for example, SA
Left PMV REL to SA Left PMV REL ECU input)
Open each modulator connection making sure the correct
component and location are displayed on the LEDs:
Steer Axle Right Modulator
Steer Axle Left Modulator
Drive Axle Right Modulator
Drive Axle Left Modulator
If the vehicle is equipped with a retarder relay, is the ECU
confi gured to control the relay?
Does the ECU perform ABS properly on each wheel? Where
a test track or similar area is available, test drive the vehicle
and make sure ABS is operating correctly.
*If any of the questions were answered with a "No", the Antilock system
should be review by a qualifi ed individual. For technical assistance,
call the Bendix Technical Assistance Team at 1-800-AIR-BRAKE,
(1-800-247-2725).
S-1503 ©2007 Bendix Commercial Vehicle Systems LLC 8/07 Printed in U.S.A. All Rights Reserved.
CONTACTING BENDIX
yes
no*
www.Bendix.com
The Bendix on-line troubleshooting guides help
you determine the cause of most performance
issues with the braking system. For additional
troubleshooting information please see the
Service Data sheet included in this kit.
The Bendix on-line contacts guide will make
it easy for you to fi nd the Bendix contacts you
need. From this page, you can navigate to
technical support contacts, Service Engineers,
Bendix Account Managers, international contacts
and more. Bendix.com is your complete Bendix
resource.
Bendix Technical Assistance Team
For direct personal technical support, call the
Bendix technical assistance team at 1-800-AIR-
BRAKE (1-800-247-2725-2-1), Monday through
Friday, 8:00 A.M. to 6:00 P.M. EST, and follow
the instructions in the recorded message.
Or, you may e-mail the Bendix technical
assistance team at: [email protected].
To better serve you, please record the following
information before calling the Bendix Tech
Team:
Bendix product model number, part number and
confi guration.
Vehicle make and model.
Vehicle confi guration. (Number of axles, tire
size, etc.)
System performance symptoms. When do they
occur?
What faults have been identifi ed using blink
codes or diagnostic tools?
What troubleshooting / measurements have
been performed?
What Bendix service data literature do you have
or need?
3