Dyna-Glo Delux RMC-FA300DGD Gebruiksaanwijzing & onderdelenhandleiding - Pagina 9
Blader online of download pdf Gebruiksaanwijzing & onderdelenhandleiding voor {categorie_naam} Dyna-Glo Delux RMC-FA300DGD. Dyna-Glo Delux RMC-FA300DGD 12 pagina's. Delux propane construction heater
Ook voor Dyna-Glo Delux RMC-FA300DGD: Gebruiksaanwijzing & onderdelenhandleiding (11 pagina's)
Pagina afdrukken
Dyna-Glo
Delux Operating Instructions and Parts Manual
TM
ProFitter
& Dyna-Glo
TM
TM
Dyna-Glo
ProFitter
Propane Construction Heater
Troubleshooting Chart
Symptom
Fan does not turn when
electrical connection is
made
Troubleshooting Chart
Symptom
Fan does not turn when
electrical connection is
made
Heater will not fire
Heater quits while
Heater will not fire
running
Heater quits while
Always be sure to follow proper maintenance procedures, by cleaning the heater once per month during regular
running
usage, and check spark gap at least once per season.
WARRANTY:
SERVICE AND LIMITED WARRANTY
Always be sure to follow proper maintenance procedures, by cleaning the heater once per month during regular
GHP Group, Inc., warrants this product to be free from defects in materials and components for one (1) year from the date of first purchase, provided that the product
usage, and check spark gap at least once per season.
has been properly installed, operated and maintained in accordance with all applicable instructions. To make a claim under warranty the Bill of Sale or cancelled
check must be presented.
This warranty is extended only to the original retail purchaser. This warranty covers the cost of part(s) required to restore this heater to proper operating condition and
an allowance for labor when provided by a GHP Group, Inc., Authorized Service Center. Warranty part(s) MUST be obtained through authorized dealers of this
product and/or GHP Group, who will
provide original factory replacement parts. Failure to use original factory replacement parts voids this warranty. The heater MUST be installed by a qualified installer in
accordance with all local codes and instructions furnished with the unit.
This warranty does not apply to parts that are not in original condition because of normal wear and tear, or parts that fail or become damaged as a result of misuse,
accidents, lack of proper maintenance or defects caused by improper installation. Travel, diagnostic cost, labor, transportation and any and all such other costs
related to repairing a defective heater will be the responsibility of the owner.
TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT GOVERNS THE SALE OF THE PRODUCT; THIS EXPRESS WARRANTY EXCLUDES
ANY AND ALL OTHER EXPRESSED WARRANTIES AND LIMITS THE DURATION OF ANY AND ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE TO ONE (1) YEAR FROM THE DATE OF FIRST
PURCHASE PRICE OF THE PRODUCT AND GHP GROUP INC., PRODUCTS SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES WHATSOEVER INCLUDING
INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of incidental or consequential damages, so the above limitation on
implied warranties, or exclusion or limitation on damages may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.
Contact GHP Group, Inc., for consumer information, technical assistance and to obtain
replacement parts at 1-877-447-4768. You will need to provide the following information when communicating with the help desk:
For Technical Support or Troubleshooting, Call: 1-877-447-4768, 8:30 am - 4:30 pm CST
Operating Instructions and Parts Manual
& Dyna-Glo
TM
TM
Possible Cause(s)
1. No electric power to heater
2. Fan blade contacts inside of heater
Possible Cause(s)
housing
3. Fan blade(s) bent
1. No electric power to heater
4. Fan motor defective
1. No spark at igniter
2. Fan blade contacts inside of heater
housing
2. Improper spark gap
3. Fan blade(s) bent
3. Bad electrode
4. Fan motor defective
1. Internal temperature too high causing
1. No spark at igniter
limit switch to shut down operation
2. Damaged control valve
2. Improper spark gap
3. Dust or debris build-up inside of heater
3. Bad electrode
1. Internal temperature too high causing
limit switch to shut down operation
2. Damaged control valve
3. Dust or debris build-up inside of heater
• Heater type and model number
• Serial Number
• Description of the part or problem
GHP Group, Inc., Skokie, IL 60076-4034 / Phone: 1-877-447-4768
TM
Corrective Action
NEVER LEAVE THE HEATER
1. Check current to electric outlet. If voltage is
UNATTENDED WHILE BURNING!
correct, check power cord and extension cord for
cuts and breaks
2. Be sure that housing is not damaged. Make sure
Corrective Action
there are no obstructions to the fan
3. Straighten blade(s) to match others
1. Check current to electric outlet. If voltage is
4. Replace motor
correct, check power cord and extension cord for
cuts and breaks
1. Check igniter wire. Reattach or tighten if loose.
Check spark module. Replace if necessary. Check
2. Be sure that housing is not damaged. Make sure
all electrical components
there are no obstructions to the fan
2. Set gap to 0.08"
3. Straighten blade(s) to match others
3. Replace spark plug
4. Replace motor
1. If the heaters output is restricted, internal tem-
1. Check igniter wire. Reattach or tighten if loose.
perature becomes too high. Move heater away
Check spark module. Replace if necessary. Check
from any obstructions
all electrical components
2. Replace control valve
2. Set gap to 0.08" (2 mm)
3. Clean inside of heater
3. Replace spark plug
1. If the heaters output is restricted, internal tem-
pera ture becomes too high. Move heater away
from any obstructions
2. Replace control valve
3. Clean inside of heater
9
RMC-FA300DGD
RMC-FA300PF/DG/DGD
www.ghpgroupinc.com