Gage Bilt GB50 Originele handleiding - Pagina 6

Blader online of download pdf Originele handleiding voor {categorie_naam} Gage Bilt GB50. Gage Bilt GB50 9 pagina's. Pneumatic installation tool

Pagina afdrukken

WARNING:

The balance of the tool is designed for horizontal use and is not suited for any other application. Gage Bilt will

be pleased to advise for your specific application.

The GB50 pneumatic riveter is designed specifically for the most efficient installation of a wide range of blind rivets. It will install

aluminum rivets through 5/32" diameter, and through 1/8" diameter rivets in any material. It weighs only 1.8 lbs. (0.82 kg) and can be

operated in any position with one hand.

The GB50 Riveter is 7.31" (185.7mm) high, has a .740" (18.8mm) stroke and generates a minimum of 600 lbs. (2.67kN) of pull at 90

psi (6.2 bar). It operates from 90 psi (6.2 bar)-100 psi (6.9 bar) of air pressure at the tool.

The air inlet is provided with 1/4-18 female pipe threads to accept the users air hose fitting.

NOSE ASSEMBLIES ARE NOT FURNISHED WITH THIS TOOL AND MUST BE PURCHASED SEPARATELY.

WARNING:

Maintenance personnel

WARNING:

Disconnect tool from its power source before performing maintenance.

The performance of any tool depends upon good maintenance practices. Following these minimal requirements for service and care

will extend the life of your tool.

*Only use a clean dry air supply set at 90-100 p.s.i. (6.2-6.9 bar) Max. equipped with a filter-regulator to prevent wear.

*Proper care by operator is necessary in maintaining full productivity and reducing downtime. Read all applicable tool manuals and

nose assembly data sheets prior to operating tools.

*Keep nose assemblies, especially jaws, clean and free of chips and debris. Lube jaws and collet surfaces that jaws ride on with

light machine oil on a daily basis.

*All Screwed End Caps, Base Covers, Air Fittings, lever, Screws and Nose Assemblies are to be examined at the end of each

working shift to check that they are secure.

*Check tool, all hoses and all couplings daily for damage or air leaks. Tighten or replace (if necessary).

*A complete overhaul can be achieved by the use of Service Kit (500000) which contains a complete set of o'rings, retaining rings,

screws, and pins. It is recommended that this service kit be kept available for spare parts.

Disconnect air hose from tool. The performance of any tool depends on good maintenance practices. This tool could require periodic

replacement of seals and o'rings. The seals requiring most frequent replacement are the o'rings (400858) and the o'ring (400807). The

cushion (510114) will eventually require replacement with use. Keep the exhaust port, in the back, clear of debris at all times. Disas-

sembly of the head portion of the tool is accomplished as follows: Using a Truarc® plier, remove retaining ring (S15) which al-

lows removal of back cap (510118) and cushion (510114). Double nut front end of drawbolt (510217) using 1/4-28 nut, then re-

move connector bolt (500120) permitting removal of retaining ring (S15) and rear piston (510101). Remove front retaining ring (S15)

and withdraw front seal (510119). Remove the front piston (510101), permitting removal of the sleeve (510104). The triple piston

chambers are separated by dividers (510102) which may be removed by removing the rings (S15).

viders (510102), care should be taken to replace the retaining rings (S15) so they do not block the air ports at the bottom of the

head cylinder ass'y (541119) where the handle (510322) attaches.

CLEANING AND LUBRICATING PROCEDURE

Daily cleaning and lubrication of nose assembly will greatly reduce downtime

and increase life of components. Using sewing machine oil, or an equivalent

cleaner/lubricant, follow instructions below.

1. Disconnect tool vacuum line (if equipped).

2. Point nose assembly into oil as shown (Fig. A).

3. Cycle tool 8-10 times and wipe dry.

GB50 S/N: 1476 AND ABOVE

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

DESCRIPTION

MAINTENANCE

MUST

read and understand all warnings and cautions.

Caution:

When replacing the di-

Image may not

reflect actual tool

Fig A.

Rev. 5/15