Dyna-Glo RMC-FA150NGDGD Gebruiksaanwijzing & onderdelenhandleiding - Pagina 3
Blader online of download pdf Gebruiksaanwijzing & onderdelenhandleiding voor {categorie_naam} Dyna-Glo RMC-FA150NGDGD. Dyna-Glo RMC-FA150NGDGD 10 pagina's. Natural gas construction heater
Ook voor Dyna-Glo RMC-FA150NGDGD: Gebruiksaanwijzing & onderdelenhandleiding (11 pagina's)
Pagina afdrukken
Dyna-Glo Delux Operating Instructions and Parts Manual
Model RMC-FA150NGDGD
General Safety Information
(Continued)
– This heater is equipped with a thermo-
stat. Heater may start at anytime.
– Never move, handle, or service a hot,
or operating heater. Severe burns may
result. You must wait 15 minutes after
turning heater off.
– To prevent injury, wear gloves when
handling heater.
– Never attach ductwork to heater.
– Do not alter heater. Keep heater in its
original state.
– Do not use heater if altered.
– Turn off natural gas supply to heater
and unplug when not in use.
– This heater is not to be used with
external thermostats, timers or other
devices that control or alter electrical
supply to the heater.
Clean
Heated
Air Out
(Front)
Combustion Chamber
Air Combustion
and Heating
Figure 2 – Cross Section Operational View
For Technical Support or Troubleshooting, Call: 1-877-447-4768, 8:30 am - 4:30 pm CST
Principals of Operation
FUEL SYSTEM
The pipe runs from the gas supply to
the heater itself. After the gas runs
through the pipe, it passes through
the solenoid valve and out the nozzle
into the combustion chamber.
AIR SYSTEM
The internal motor turns the fan, which
pushes air around and through the
combustion chamber. Here the air is
heated and provides a constant stream
of warmth.
IGNITION SYSTEM
The spark module sends voltage to the
ignitor. The ignitor ignites the fuel and
air mixture.
SAFETY CONTROL SYSTEM
This system shuts the heater down if
the flame is extinguished. The fan and
motor will continue to operate, but
there will not be any heat.
Nozzle
Motor
Ignitor
Fan
On/Off Switch
Solenoid Valve
Regulator
Spark Module (Spark Ignitor)
PCB Control
Fuel
3
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
TEMPERATURE CONTROL SYSTEM
A built-in thermostat allows the heater
to turn on and off to maintain a
consistent temperature.
THE NATURAL GAS SUPPLY
The user of this heater must provide
the natural gas supply and all fittings to
properly install the heater.
The natural gas supply should be able
to provide a minimum of 150 cubic feet
of gas per hour for each heater being
used. Consult with your natural gas
supplier for the proper sizing of all gas
lines. You must regulate the natural
gas supply down from a minimum of 5
inches of water column to a maximum
of 1/2 PSI.
Be sure to research and follow all local
ordinances and codes. In the absence of
local codes, follow the National Fuel Gas
Code Handbook NFPA54/ANSI Z223.1
and the Natural Gas Installation Code,
CAN/CSA B149.1.
Ventilation
WARNING
outside air must be provided to operate
each heater safely. If the proper air vent
ilation is not provided, carbon monoxide
poisoning can occur. Always be sure that
the proper ventilation is being provided
before starting this heater.
Power Cord
A three square foot
opening of fresh
www.ghpgroupinc.com
PROFESSIONAL GRADE