Hi-Force AHP1122R Series Gebruiksaanwijzing - Pagina 2
Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Hi-Force AHP1122R Series. Hi-Force AHP1122R Series 8 pagina's. Air driven hydraulic pumps
Ook voor Hi-Force AHP1122R Series: Gebruiksaanwijzing (8 pagina's)
Pagina afdrukken
INSTRUCTION MANUAL – AIR DRIVEN HYDRAULIC PUMPS:
Model Series: AHP1120, AHP1120R, AHP1121, AHP1121R, AHP1122, AHP1122R, AHP1141, AHP1142,
HAP21011, HAP21012, HAP21014, HAP21016, HAP21021, HAP21022, HAP21024, HAP21026, HAP21031,
HAP21032, HAP21034, HAP21036, HAP21041, HAP21042, HAP21044, HAP21046,
Always operate the system under no load
condition prior to the actual lift to ensure that
no air is trapped in the hydraulic circuit.
Do not drop or place heavy objects on a
hydraulic hose as this will cause internal
damage to the hose which could result in
rupture when the hose is pressurized and could
result in serious damage to components, and
possible serious personal injury to operating
personnel.
3.0 Description AHP series Air Driven Pumps.
The device supplied is an air-powered
hydraulic pump that converts a compressed air
supply into a pressurized hydraulic flow (see
"Technical specifications" – table below Fig 2).
The pump can be utilized to power single and
double acting hydraulic cylinders; in the latter
case a directional control valve between
pump and cylinder is required. The filler/
breather plug can be removed and used as a
return line. (or select model AHP 1141/ 1142).
Any other uses of the pump shall be considered
improper and can cause serious accidents. The
manufacturer declines all liability for damages
resulting from improper use of the pump.
The main components of the pump
Note: Models ending with "R" (AHP1120R/
1121R/ 1122R) are operated with a hand
pendant instead of a treadle (Fig 16).
4.0 Safety:
Observe all the following safety rules. They are
of the maximum importance for your own
safety and the safety of others. In addition to
the safety warnings in this section, please also
take note of all safety related issues in other
sections of this manual.
DO NOT TAMPER WITH THE PROTECTIONS
AND SAFETY DEVICES AND DO NOT
MODIFY THE PUMP IN ANY WAY TO
AVOID CREATING POTENTIALLY
HAZARDOUS SITUATIONS FOR WHICH
THE OPERATOR OR THE SERVICE
TECHNICIAN IS UNPREPARED.
REMOVING OR TAMPERING WITH ANY
OF THE SAFETY DEVICES ON THE PUMP
Hi‐Force Limited – Prospect Way – Daventry – Northants NN11 8PL – United Kingdom
Tel: +44(0) 1327 301000: Fax: +44(0) 1327 706555: Website: www.hi‐force.com
AUTOMATICALLY INVALIDATES THE
WARRANTY AND ABSOLVES THE
MANUFACTURER FROM ALL LIABILITY
5.0 Installation and start up:
If these instructions are disregarded, the person
who is responsible for the modifications
automatically assumes full liability for any
accidents that may occur during use of the
pump.
Pump model AHP
1120/1120R/1121/1121R/1122/1122R/1141/1142
can be installed in a horizontal or vertical
position.
5.1. Filling the reservoir (if the pump is supplied
without oil)
The table above (Fig 2.) shows the oil quantities
required to fill the pump reservoir. The table
also shows the actual usable oil capacities.
Use only HI-FORCE HFO46 oil for your AHP
Pump.
The manufacturer shall not be held responsible
for injury to people or damage to property
caused by the use of incorrect hydraulic oil.
Damage to the pump resulting from the above
mentioned causes is not covered by warranty.
Use a slotted tip screwdriver to remove
the filler plug (Fig:1)
Pour the correct quantity of oil into the
reservoir (see table at Fig:2)
Clean the edges of the filler opening
with a clean cloth and refit the plug,
pressing it down fully.
5.2.1 - Pump hydraulic connections Models
AHP1120/ AHP1121/ AHP1122
Connect the hydraulic pressure hose to
(Port A Fig:14). The hose must be fitted
with a 3/8" NPTF fitting after binding the
thread with Teflon tape.
Unscrew the breather screw (Fig: 6) by
three or four turns using an appropriate
screwdriver.