Dynabrade 50307 Handmatig - Pagina 4

Blader online of download pdf Handmatig voor {categorie_naam} Dynabrade 50307. Dynabrade 50307 4 pagina's. 4-1/2"– 5" vertical disc sander

Pagina afdrukken

Disassembly/ ssembly Instructions – Vertical Disc Sander (cont.)

Motor Assembly:

1. Hold the vane slot portion of the 07104 Rotor in a vise with aluminum or bronze jaws so that the threaded spindle of the rotor is pointing up.

2. Select .003" (.08 mm) thickness in shims from the 01277 Shim Pack. Install the shims into the 07120 Bearing Plate and install the 02552 Bearing

into the bearing plate.

3. Install the bearing/plate assembly onto the 07104 Rotor and secure the assembly in place with the 07135 Rotor Nut. (Torque to 23 N•m/200 in.- lbs.)

4. Use a .001" (.03mm) feeler gauge to check the gap clearance between the bearing plate and the face of the vane slot portion of the rotor.

5. The gap clearance should be .001" (.03 mm) to .0015" (.04 mm). If the gap clarence needs adjustment repeat steps 2-4 adding or removing

shims as required.

6. Lubricate the 07107 Blades (5) with the 95842 Dynabrade Air Lube (10W/NR or equivalent) and install these into the vane slots in the motor.

7. Install the 07118 Cylinder over the 07104 Rotor so that the air inlet opening of the cylinder will line up with the air inlet opening in the

07114 Bearing Plate.

8. Use the 96244 Bearing Press Tool along with the 96232 Arbor Press to install the 01007 Bearing into the 07114 Bearing Plate. Rest the raised

outer diameter of the bearing press tool against the outer diameter of the 01007 Bearing and press the bearing into the bearing plate.

9. Use the raised inner diameter of the 96244 Bearing Press Tool so that it will rest against the inner diameter of the 01007 Bearing. Carefully press the

bearing/plate assembly onto the 07104 Rotor until it comes in contact with the cylinder. This will establish a snug fit between the bearing

plates and the cylinder.

10. Hold the 07135 Rotor Nut in vise with aluminum or bronze jaws so that the female threaded end of the rotor is pointing up.

11. Install the governor assembly onto the 07104 Rotor turning it counterclockwise. (Left Hand Thread) (Torque to 9 N•m/80 in.- lbs.)

12. Install the 07158 Spacer into the 04162 Housing.

13. Install the motor assembly into the 04162 Housing and orient the 01775 Pin to match the correct position of the governor cover.

14. Place the 07129 Gasket onto the 04162 Housing and then install the 07123 Governor Cover holding it in place with the 01790 Screws (4) and

the 01791 Washers (4). (Torque to 8 N•m/70 in.lbs.)

15. Install the 50275 Backing Pad, the abrasive and the 50273 Flange Nut.

Motor Assembly Complete.

Tool Assembly Complete.

Dynaswivel

Swivels 360° at two locations which

allows an air hose to drop straight to

•

the floor, no matter how the tool is held.

95462 1/2" NPT

•

Dynabrade Air Lube

•

Formulated for pneumatic equipment.

•

Absorbs up to 10% of its weight in water.

•

Prevents rust and formation of sludge.

Keeps pneumatic tools operating longer

with greater power and less down time.

95842: 1 pt. (473 ml)

95843: 1 gal (3.8 L)

•

96244 Bearing Press Tool

This tool is designed to safely press a

bearing into a bearing plate and onto a shaft.

95823 – 21 mm Open-End.

REFERENCE CONT CT INFORM TION

American National Standards Institute (ANSI) • www.ansi.org

25 West 43 Rd St., 4th Floor • New York, NY 10036 • Tel: 1 (202) 293-8020

DYN BR DE, INC.

8989 Sheridan Drive • Clarence, NY 14031-1419 • Phone: (716) 631-0100 • Fax: 716-631-2073 • International Fax: 716-631-2524

Optional

ccessories

•

96041 Motor Tune-Up Kit:

•

96232 #2 Arbor Press

•

96346 Bearing Separator

•

96214 Bearing Removal Tool

International Organization for Standardization (ISO)

www.iso.org • PO Box 56 • Ch-1211 Geneve 20, Switzerland

www.dynabrade.com

Includes assorted parts to help maintain

and repair motor.

This arbor press is ideal for the disassembly

and assembly of air motors.

Use the separator to remove

gears and bearings.

This tool is designed to pass through the

I.D. of the bearing plate and push against

the I.D. of the bearing.