Dynabrade Dynorbital-Spirit 59011 Veiligheid, bediening en onderhoud - Pagina 8
Blader online of download pdf Veiligheid, bediening en onderhoud voor {categorie_naam} Dynabrade Dynorbital-Spirit 59011. Dynabrade Dynorbital-Spirit 59011 13 pagina's. 12,000 rpm air powered random orbital sander 3/8" orbit 3/16" orbit 3/32" orbit
Pagina afdrukken
Motor Assembly/Disassembly Instructions - Dynorbital -Spirit
Drawing 3
To Assemble (Continued):
10. Place 59055 Bearing Plate (with 58368 Bearing pressed into place) over shaft and "long" end of line-up pin and press fit in place as
shown in Drawing 4.
11. Install 98463 Snap Ring in groove.
12. Place 01024 O-Ring into recess in side wall of cylinder.
13. Install 50569 O-Ring into 59058 Lock Ring. Slide the lock ring assembly over the motor shaft balancer (3/32" and 3/16" orbits only). Apply 1 drop of
pneumatic tool oil and spread between the motor bearing plate and 50569 O-Ring.
14. Place 1 drop of pneumatic tool oil on 01024 O-Ring.
15. Secure motor housing in vise, using 57092 Collar or padded jaws. Slide motor assembly into second housing. Note: Be certain line-up post enters the
notch in the bottom of the housing and 01024 O-Ring stays seated in cylinder.
16. Tighten lock ring with 56058 Lock Ring Tool to 23 N•m/200 in.-lbs. Attach weight-mated sanding pad.
Valve and Speed Regulator Assemblies:
1. Secure housing in vice using 57092 Collar or padded jaws.
2. Remove inlet bushing, 01468 Spring, 58365 Tip Valve and 01464 Seal from housing. Remove 98927 Pin from housing and lever.
3. Remove 95697 Snap Ring. Press the speed regulator and valve stem out of the housing. Remove the 01025 O-Rings (2) and 98459 O-Ring.
4. Place new 01025 O-Rings (2) on the speed regulator and a new 98459 O-Ring on the valve stem. Then place in housing with valve stem. Install new
95967 Snap Ring. Apply a small amount of pneumatic tool oil to valve o-rings.
5. Place new 01464 Seal in housing. Using tweezers or needle nose pliers, place the tip valve into housing so that the tip valve goes under the valve
stem. Place new 01468 Spring into housing so small end is towards tip valve.
6. Apply a small amount of #567 Loctite
7. Install Lever on housing with 98927 Pin centered on housing.
Note: Motor should operate at between 11,000 and 12,000 RPM at 6.2 bar (90 PSIG). RPM should be checked with a tachometer. Before operating,
we recommend that 2-3 drops of Dynabrade Air Lube P/N 95842 (or equivalent) be placed directly into the air inlet with throttle lever depressed. Operate the
machine for approximately 30 seconds before application to workpiece to determine if machine is working properly and safely and to allow lubricating
oils to properly dispense through machine.
Loctite
®
is a registered trademark of the Loctite Corp.
Disc Pad Change:
1. Insert 50679 Wrench on flats of 59059 Balancer Shaft and twist off sanding pad by hand.
2. With wrench still in place, hand tighten new pad on tool.
3. No need to remove shroud or overskirt.
Required Weight of Pads:
3" Models –– Use pad weighing 75g.
3-1/2" Models –– Use pad weighing 80g.
5" Models –– Use pad weighing 100g.
6" Models –– Use pad weighing 130g.
57091
Bearing Press Tool
59055
Front Bearing Plate
58368 Bearing
Motor Shaft Balancer
Balancer Shaft Assembly
®
(or equivalent) around the threads of the first inlet bushing and tighten into housing to 23 N•m/200 in. - lbs.
Drawing 4
8
57091
Bearing Press Tool
59055 Bearing Plate
(with 58368 Bearing)
Line-Up Pin
59051 Cylinder Assembly
(w/Rotor and Vanes)
59055 Front Bearing Plate
(with 58368 Bearing)
Motor Shaft Balancer
Balancer Shaft Assembly
™