Dynabrade 66402 Gebruiksaanwijzing - Pagina 5

Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Dynabrade 66402. Dynabrade 66402 6 pagina's. Tool post grinder-machine

Pagina afdrukken

Important Operating, Maintenance and Safety Instructions

Carefully read all instructions before operating or servicing any Dynabrade

Important: All Dynabrade Rotary Vane air tools must be used with a Filter-Regulator-Lubricator to maintain all warranties.

Operating Instructions:

Warning: Eye, face, respiratory sound and body protection must be worn while operating power tools. Failure to do so may result in serious

injury or death Follow safety procedures posted in workplace.

1. With power source disconnected from tool, securely fasten tool to lathe (see Mounting and Machine Adjustment Instructions, page 3).

2. Install Abrasive Belt on tool (see Abrasive Belt Change/Installation Instructions, page 3).

3. Operate machine for 30 seconds prior to application to work piece to determine if machine is working properly and safely before work begins.

Maintenance Instructions:

Products offered by Dynabrade should not be converted or otherwise altered from original design without the expressed written

consent from Dynabrade, Inc..

1. Check tool speed with tachometer. If tool is operating at a higher speed than the RPM marked on the tool or operating improperly, the

tool should be serviced to correct the cause before use.

2. Some silencers on air tools may clog with use. Clean and replace as required.

3. All Dynabrade Rotary Vane air motors should be lubricated with two drops of Dynabrade Air Lube (P/N 95842: 1pt. 473ml.) every four

hours of use.

4. An Air Line Filter-Regulator-Lubricator must be used with this air tool to maintain all warranties. Dynabrade recommends the following:

11141 Air Line Filter-Regulator-Lubricator — Provides accurate air pressure regulation, two-stage filtration of water contaminants and

positive-drip lubrication of pneumatic components. Operates 55 SCFM @ 100 PSIG has 1/2" NPT female ports.

5. Good house keeping is essential to insure long life of any machine tool. By keeping machine clean and visually inspected for any wear,

the machine will provide many years of quality service. Repair or replacement of worn parts early enough will prevent other parts

from becoming damaged.

Safety Instructions:

Products offered by Dynabrade should not be converted or otherwise altered

from original design without expressed written consent from Dynabrade, Inc.

• Important: User of tool is responsible for following accepted safety codes such as those published by the American National Standards Institute

• Operate machine for 30 seconds before application to workpiece to determine if machine is working properly and safely before work begins.

• Always disconnect power supply before changing abrasive or making machine adjustments.

• Inspect abrasives and accessories for damage or defects prior to and during operation of tool.

• Please refer to Dynabrade's Warning/Safety Operating Instructions Tag (Reorder No. 95903) for more complete safety information.

• Never use an abrasive belt that is narrower than the contact wheel. The uncovered wheel face can cause snagging of workpiece and also

cause premature wear of contact wheel.

• Always use an upward stroke of the workpiece against the abrasive belt and use the grind area below the center line of the contact wheel.

• Warning: There is a potential combustion hazard if ferrous and non-ferrous grinding dust is mixed. Do not grind materials of different types

without thoroughly cleaning grinding residue from inside the machine.

All Dynabrade motors use the highest quality parts and metals available and are machined to exacting tolerances. The failure of quality

pneumatic motors can most often be traced to an unclean air supply or the lack of lubrication. Air pressure easily forces dirt or water contained

in the air supply into motor bearings causing early failure. It often scores the cylinder walls and the rotor blades resulting in limited efficiency

and power. Our warranty obligation is contingent upon proper use of our tools and cannot apply to equipment which has been subjected to

misuse such as unclean air, wet air or a lack of lubrication during the use of this tool.

Note: To order replacement parts specify the model and serial number of your machine.

Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within one

year from the date of purchase, all equipment of our manufacture is warranted against defects in workmanship and materials under normal

use and service. We shall repair or replace at our factory, any equipment or part thereof which shall, within one year after delivery to the

original purchaser, indicate upon our examination to have been defective. Our obligation is contingent upon proper use of Dynabrade tools in

accordance with factory recommendations, instructions and safety practices. It shall not apply to equipment which has been subject to

misuse, negligence, accident or tampering in any way so as to affect its normal performance. Normally wearable parts such as bearings,

contact wheels, rotor blades, etc., are not covered under this warranty.

Notice

Full One Year Warranty

Abrasive Power Tool.