Dynabrade 400 RPM Gebruiks- en onderhoudsinstructies - Pagina 4
Blader online of download pdf Gebruiks- en onderhoudsinstructies voor {categorie_naam} Dynabrade 400 RPM. Dynabrade 400 RPM 4 pagina's. .7 hp dynisher abrasive power tool
Pagina afdrukken
Disassembly/Assembly Instructions (continued)
7. Slip 94523 Inlet Adapter through muffler assembly and install 95711 Retainer Ring into groove on inlet adapter.
8. Install 01565 Air Control Ring into housing.
9. Apply Loctite
#567 to threads of 94523 Inlet Adapter and install entire muffler assembly onto housing inlet (torque 23.0 N•m/200 in. - lbs.).
®
10. Replace air fitting. Secure inlet adapter with a wrench before tightening air fitting.
11. Install throttle lever and 01017 Pin.
Tool Assembly is complete. Please allow 30 minutes for adhesives to cure before operating tool.
Important: Motor should now be tested for proper operation at 90 PSIG. If motor does not operate properly or operates at a higher RPM than marked on the
tool, the tool should be serviced to correct the cause before use. Before operating, place 2-3 drops of Dynabrade Air Lube (P/N 95842) directly into air inlet
with throttle lever depressed. Operate tool for 30 seconds to determine if tool is operating properly and to allow lubricating oils to properly penetrate motor.
Loctite
®
is a registered trademark of Loctite Corp.
Visit Our Web Site: www.dynabrade.com
DYNABRADE, INC., 8989 Sheridan Drive • Clarence, NY 14031-1490 • Phone: (716) 631-0100 • Fax: 716-631-2073 • International Fax: 716-631-2524
DYNABRADE EUROPE S.àr.l.,
© DYNABRADE, INC., 2004
Optional Accessories
®
Dynaswivel
Swivels 360° at two locations which allows an
air hose to drop straight to the floor, no matter
how the tool is held.
Note: For proper connection to a 1/4" NPT
thread a reducing bushing is required.
•
95461 3/8" NPT.
94473 Dynacushion
®
Pneumatic Wheel
•
Easily regulate hardness by air pressure.
•
5" Diameter x 3-1/2" Wide.
•
Inflates to 20 PSIG maximum.
•
3-1/2" wide x 15-1/2" long belt size.
95542 Grease 10 oz.
•
Multi-purpose grease for all types of bearings,
cams, gears.
•
High film strength; excellent resistance to
water, steam, etc.
•
Workable range 0˚ F to 300˚ F.
95541 Push-type Grease Gun
•
One-hand operation
Zone Artisanale • L-5485 Wormeldange—Haut, Luxembourg • Telephone: 352 76 84 94 1 • Fax: 352 76 84 95 1
53159 Shroud Assembly
•
Extended length to enclose 4 inch wide
abrasive accessories.
Email: [email protected]
PRINTED IN USA
96234 Motor Tune-Up Kit
•
Includes assorted parts to help
maintain and repair motor.
94465 Wheel Inflation Tool
•
Controlled inflation/deflation of
pneumatic wheel.
•
Has 1/4" female thread; fits 1/4" air hose.
•
95633 Nozzle Replacement available.
Dynabrade Air Lube
•
Formulated for pneumatic equipment.
•
Absorbs up to 10% of its weight in water.
•
Prevents rust and formation of sludge.
•
Keeps pneumatic tools operating longer
with greater power and less down time.
95842: 1pt. (473 ml)
95843: 1gal. (3.8L)
DYNABRADE
PD01.40_Rev.1_02/04
®