Dynabrade 51401 Veiligheid, bediening en onderhoud - Pagina 4
Blader online of download pdf Veiligheid, bediening en onderhoud voor {categorie_naam} Dynabrade 51401. Dynabrade 51401 4 pagina's. 4 hp, 7 degree, rear exhaust buffer
Pagina afdrukken
carrier. Torque to 17 N-m/150 in. lbs.
12. Install planetary gears and 54472 Gear Shafts onto planetary housing.
13. Slip 54468 Ring Gear over gears making sure that notches in ring
gear will align with lock screw and grease fitting in 50776 Housing
once planetary gear assembly is installed.
14. Press rear 54552 Bearing onto 50786 or 50787 Planetary Carrier,
until the outer race of the bearing touches the ring gear.
15. Slip the complete planetary gear assembly into 50776 Housing and
install 50784 Lock Screw.
16. Install 50781 Rear Exhaust Cover onto 50776 Housing.
Use 50971 Lock Ring Tool, torque to 28 N-m/250 in. lbs.
17. Lubricate planetary gears through 01041 Grease Fitting
with two plunges every 50 hours of use for maximum gear life.
18. Install back-up pad.
VALVE BODY ASSEMBLY:
1. Insert 01469 Regulator with o-rings and valve stem in place into valve
body. Secure with 95558 Retaining Ring.
2. Secure valve body in vise using 52296 Repair Collar with air inlet
facing upwards. Insert 01464 Seal.
3. Line up hole in valve stem with hole in housing (looking past brass
bushing). Insert 01472 Tip Valve so that the metal pin passes through the
hole in the valve stem. Install 01468 Spring (small end towards tip valve).
4. Roll 94528 Felt Muffler and place into 94522 Muffler Cap. I
nstall 94521 Muffler Base onto muffler cap.
5. Install 95438 O-Ring into groove on muffler base. Place 95375 O-Ring
and 94526 Spacer into recessed area of muffler cap.
6. Slip 94523 Inlet Adapter through muffler assembly and install 95711
Retainer Ring into groove on inlet adapter.
MACHINE SPECIFICATIONS
Model
Speed
51400
3,200 RPM
51401/51403
5,000 RPM
51430
3,200 RPM
Additional Specifications: Air Inlet Thread 1/4" NPT • Hose I.D. 3/8" (10 mm) ● Visit dynabrade.com for your model's current vibration and sound data.
OPTIONAL ACCESSORIES
Dynaswivel
Part No. 94300
•
Patented "universal-joint" connects
portable air tools to an air line.
•
Swivels 360° AT TWO PIVOT POINTS
allowing the air hose to drop directly
to the floor while providing superb
tool handling.
•
New lightweight, non-marring composite
construction; industrial quality.
Repair Collar
Part No. 52296
•
Specially designed collar for use in vise
to prevent damage to valve body
housing during disassembly/assembly.
50971 Lock Ring Tool
•
Lock Ring Tool has a 3/8 in. square socket
for use with 3/8 in. drive; breaker bar,
ratchet head, or torque wrenches.
Open-End Wrench
Part No. 95262 – 14mm open-end.
REFERENCE CONTACT INFORMATION
American National Standards Institute (ANSI)
www.ansi.org
Compressed Air & Gas Institute (CAGI)
www.cagi.org
DYNABRADE, INC.
8989 Sheridan Drive • Clarence, NY 14031-1419 • Phone: (716) 631-0100 • Fax: 716-631-2073 • International Fax: 716-631-2524
© DYNABRADE, INC., 2020
Power
Sound Level
Air Consumption
80 dB(A)
.4 hp
78 dB(A)
(680 LPM)
(298 W)
80 dB(A)
®
(1/4" NPT)
European Committee for Standardization (PNEUROP)
www.pneurop.org
International Organization of Standards (ISO)
www.iso.org
7. Install 01564 Air Control Ring into valve body housing.
8. Apply Loctite #567 PST Pipe Sealant to threads of 94523 Inlet Adapter and
install entire muffler assembly onto valve body (torque 23.0 N•m/200 in. - lbs.).
9. Replace air fitting.
Secure inlet adapter with a wrench before tightening air fitting.
10. Install throttle lever and 12132 Pin.
TOOL ASSEMBLY COMPLETE.
PLEASE ALLOW 30 MINUTES FOR ADHESIVES TO
CURE BEFORE OPERATING TOOL.
NOTICE: To adjust throttle body orientation for a rear exhaust tool:
1. Use 52296 Repair Collar to secure valve body in vise with
50776 Housing facing up.
2. Peel down 01558 Collar to expose the hex portion of 01461 Lock Nut.
3. Using a 34mm crows foot and firmly holding motor housing, turn 01461
Lock Nut counter clockwise to loosen assembly.
4. Adjust orientation of the throttle lever to agree with your grip and
comfort level allowing for additional rotation due to torquing.
5. Using the 34mm crows foot and a torque wrench set to 400 lb. in.,
(while firmly holding motor housing in place to reduce housing rotation)
tighten 01461 Lock Nut.
IMPORTANT: Motor should now be tested for proper operation at 90 PSIG.
If motor does not operate properly or operates at a higher RPM than marked
on the tool, the tool should be serviced to correct the cause before use. Before
operating, place 2-3 drops of Dynabrade Air Lube (P/N 95842) directly into air
inlet with throttle lever depressed. Operate tool for 30 seconds to determine if
tool is operating properly and to allow lubricating oils to properly penetrate motor.
Loctite
®
is a registered trademark of Loctite Corp.
Pad Diameter
3" (76 mm)
24 SCFM
4"-5"
(102-107mm)
Finesse Sanding Creme
Part No. 95723: 4 oz. (118 ml).
Part No. 95724: 1 qt. (946 ml).
Part No. 95725: 1 gal. (3.8 L).
•
A sanding compound for metal,
fiberglass and composites.
Use with fine-grade sanding
discs.
Dynabrade Glaze
•
For use with slow-speed
tools to achieve a high
gloss after compounding.
Part No. 95727: 4 oz. (118 ml).
Part No. 95728: 1 qt. (946 ml).
Grease 10 oz.
Part No. 95542
•
Multi-purpose grease for all
types of bearings, cams, gears.
•
High film strength; excellent
resistance to water, steam, etc.
•
Workable range 0˚ F to 300˚ F.
Push-type Grease Gun
Part No. 95541
•
One-hand operation.
www.dynabrade.com
Spindle Thread
Weight
1.7 lbs.
(.8 kg)
3/8"-24 Male
2.4 lbs.
(1.1 kg)
Motor Tune-Up Kit
Part No. 96174
•
Includes assorted
parts to help maintain
and repair motor.
"Flat-Face" Foam Buffs
•
Velcro-backed for easy
attachment/removal.
•
Excellent absorption of
excess compound/glaze.
3" diameter
90038
•
Prevents swirls.
•
Two sizes to choose from:
3"– 90038
•
Use with models 51400.
5" diameter
5"– 90040
90040
•
Use with models 51430, 7° Buffer.
3" diameter
90027
Terry Cloth
U.S. Government Publishing Office (GPO)
www.gpo.gov
Length
Height
4-1/4"
8-3/4"
(222 mm)
(108 mm)
9-3/4"
4-1/2"
(248 mm)
(114 mm)
3" diameter
90029
Synthetic Wool