Dynabrade 53455 Bedienings-, onderhouds- en veiligheidsinstructies - Pagina 6

Blader online of download pdf Bedienings-, onderhouds- en veiligheidsinstructies voor {categorie_naam} Dynabrade 53455. Dynabrade 53455 6 pagina's. Dynabrade 950 rpm angle-head

Pagina afdrukken
Disassembly/Assembly Instructions – 950 RPM Mini Angle-Head Drill
2. Apply a small amount of the 95541 Grease to the 53450 Spline Drive, align and thread the angle-head housing assembly onto the double planetary
housing so that the spline drive will mesh with the 54541 Spindle. Thread the angle-head housing all the way onto the 53454 Double Planetary Housing
until it touches the 54527 Lock Ring by turning it counterclockwise. (Left Hand Threads) Back the angle-head housing off and orient it to the desired
position in relation to the throttle lever.
3. Hold the 54547 Angle-Head Housing stationary with a wrench and tighten the 54527 Lock Ring against the angle-head housing to lock the angle-head
in the desired position. (Torque to 34 N·m/300 in. lbs.)
Angle-Head Connection to the Double Planetary Housing Complete. Tool Assembly Complete.
Note: Motor should operate at 950 RPM at 6.2 bar (90 PSIG). RPM should be checked with a tachometer. Before operating, we recommend that 2-3 drops of pneumatic
tool oil be placed directly into the air inlet with throttle lever depressed. Grease gears through grease fittings.
Important: Motor should now be tested for proper operation at 90 PSIG. If motor does not operate properly or operates at a higher RPM than marked on the
tool, the tool should be serviced to correct the cause before use. Before operating, place 2-3 drops of Dynabrade Air Lube (P/N 95842) directly into air inlet
with throttle lever depressed. Operate tool for 30 seconds to determine if tool is operating properly and to allow lubricating oils to properly penetrate motor
Loctite
®
is a registered trademark of Loctite Corp.
Grease
•
Multi-purpose grease for all types
of bearings, cams, gears.
•
High film strength; excellent
resistance to water, steam, etc.
•
Workable range 0˚ F to 300˚ F
95541: Push-Type Grease Gun
(one-handed operation).
95542: 10 oz. (283.5 g) tube.
®
Dynaswivel
Swivels 360° at two locations which allows
an air hose to drop straight to the floor,
no matter how the tool is held.
•
94300 Composite Swivel 1/4" NPT.
96232 #2 Arbor Press
•
This arbor press is ideal for the
disassembly and assembly
of air motors.
52296 Repair Collar
•
Specially designed collar for use in vise to
prevent damage to valve body of tool during
disassembly/assembly.
97782 Lock Ring Tool
•
Lock Ring Tool has a 3/8 in. square socket
for use with 3/8 in. drive; breaker bar,
ratchet head, or torque wrenches.
96165 Lock Ring Tool
•
Lock Ring Tool has a 1/4 in. square socket
for use with 1/4 in. drive; breaker bar,
ratchet head, or torque wrenches.
Visit Our Web Site: www.dynabrade.com
DYNABRADE, INC., 8989 Sheridan Drive • Clarence, NY 14031-1490 • Phone: (716) 631-0100 • Fax: 716-631-2073 • International Fax: 716-631-2524
DYNABRADE EUROPE S.àr.l.,
© DYNABRADE, INC., 2003

Optional Accessories

Zone Artisanale • L-5485 Wormeldange—Haut, Luxembourg • Telephone: 352 76 84 94 1 • Fax: 352 76 84 95 1
Dynabrade Air Lube
•
Formulated for pneumatic equipment.
•
Absorbs up to 10% of its weight in water.
•
Prevents rust and formation of sludge.
•
Keeps pneumatic tools operating longer
with greater power.
95842: 1pt. (473 ml)
95843: 1gal. (3.8 L)
96333 Motor Tune-Up Kit
•
Includes assorted parts to
help maintain and repair motor.
96346 Bearing Separator
•
Use the separator to remove
bearings and gears.
96401 Metric Hex Key
•
This 2 mm hex key is used for the removal
and installation of the 50784 Set Screw.
96343 Retaining Ring Pliers
•
Internal/external retaining ring pliers
Tip diameter - .0.038" (0.96mm)
®
DYNABRADE
PRINTED IN USA