Dynabrade 15302 Montage - Pagina 7
Blader online of download pdf Montage voor {categorie_naam} Dynabrade 15302. Dynabrade 15302 8 pagina's. Air motor and machine parts
Pagina afdrukkenImportant Operating, Maintenance and Safety Instructions
Carefully read all instructions before operating or servicing any Dynabrade
Warning: Hand, wrist and arm injury may result from repetitive work motion and overexposure to vibration.
Important: All Dynabrade air tools must be used with a Filter-Regulator-Lubricator to maintain all warranties.
Operating Instructions:
Warning: Eye, face, respiratory, sound, and body protection must be worn while operating power tools. Failure to do so may result in serious injury or death.
Follow safety procedures posted in workplace.
1. With power source disconnected from tool, securely fasten abrasive/accessory on tool.
2. Connect power source to tool. Be careful not to depress throttle lever in the process.
3. Check tool speed with tachometer. If tool is operating at a higher speed than the RPM marked on the tool or operating improperly, the tool should be
serviced to correct the cause before use.
4. Always work off the return side of the abrasive belt. This will ensure superior tracking and reduce down time of tool.
Abrasive Belt/Contact Arm Change Instructions:
To Change Belt:
1. Disconnect power source.
2. Remove cover.
3. Pull back on tension arm assembly.
4. Remove and replace abrasive belt and cover.
5. Connect power source.
6. Adjust belt tracking by turning 95218 Rough Adjustment Knob
to the left or right accordingly while machine is running.
Housing Angle Adjustment:
To pivot housing, loosen 95311 Screw on housing with the supplied 9/64" hex wrench (P/N – 95134). Pivot housing to desired angle and retighten 95311 Screw.
Maintenance Instructions:
Products offered by Dynabrade should not be converted or otherwise altered from original design without the expressed written consent from Dynabrade, Inc.
1. All Dynabrade air motors should be lubricated. Dynabrade recommends one drop of air lube per minute for each 10 SCFM (example: if the tool
specifications state 40 SCFM, set the drip rate of your filter-lubricator at 4 drops per minute).
Dynabrade Air Lube (P/N 95842: 1pt. 473ml.) is recommended.
2. An Air Line Filter-Regulator-Lubricator must be used with this air tool to maintain all warranties. Dynabrade recommends the following: 11289 Air Line
Filter-Regulator-Lubricator — Provides accurate air pressure regulation, two-stage filtration of water contaminants and positive-drip lubrication of pneumatic
components. Operates 28 SCFM @ 90 PSIG has 3/8" NPT female ports.
3. Frequent drainage of water traps in air lines is recommended.
4. Some silencers on air tools may clog with use. Clean and replace as required.
5. A Motor Tune-Up Kit (P/N 96024) is available which includes assorted parts to help maintain and repair motor.
Safety Instructions:
Products offered by Dynabrade should not be converted or otherwise altered
from original design without expressed written consent from Dynabrade, Inc.
•
Warning: Eye, face and body protection must be worn while operating power tools. Failure to do so may result in serious injury or death. Follow safety
procedures posted in workplace.
•
Important: User of tool is responsible for following accepted safety codes such as those published by the American National Standards Institute (ANSI).
•
Tool RPM must never exceed abrasive/accessory RPM rating, regardless of tool capacity.
•
Operate machine for 30 seconds before application to workpiece to determine if machine is working properly and safely before work begins.
•
Always use proper guards. Make sure guards are in proper position, secure and in good repair.
•
Always disconnect power supply before changing abrasive or making machine adjustments.
•
Inspect abrasives and accessories for damage or defects prior to installation on tools.
•
Please refer to Dynabrade's Warning/Safety Operating Instructions Tag (Reorder No. 95903) for more complete safety information.
•
Warning: Hand, wrist and arm injury may result from repetitive work, motion and overexposure to vibration.
®
Abrasive Power Tool.
To Change Contact Arm Assembly:
1. Disconnect power source.
2. Remove cover.
3. Pull back on tension arm assembly and remove abrasive belt.
4. Remove 95218 Rough Adjustment Knob.
5. Remove contact arm and replace with desired arm, making sure that
tab on the end of the arm is facing downward.
6. Replace 95218 Knob.
7. Install abrasive belt and cover.
8. Connect power source and adjust belt tracking by turning 95218 Knob to the left
or right accordingly while machine is running.
7
the.