dayLux SET-DLCM3,5 (A,D) Basis gebruikershandleiding

Blader online of download pdf Basis gebruikershandleiding voor {categorie_naam} dayLux SET-DLCM3,5 (A,D). dayLux SET-DLCM3,5 (A,D) 4 pagina's. 10 way pluggable lighting control module

Pagina afdrukken

DLCS

10 WAY PLUGGABLE LIGHTING CONTROL MODULE

PRODUCT FEATURES

3 or 5 Channel control and lighting distribution.

10 x Outputs to luminaries using industry standard

'Wieland' connectors.

Capable of Dimming and / or Switching from one unit.

All common dimming protocols supported (DSI, DALI

'Broadcast' and 1-10v Analogue).

Automatic light level dimming or switching (daylight linking).

Maintains a specific Lux level and saves energy.

Manual dimming or switching - via faceplates or momentary

switches for scene selection, off, raise and lower.

Presence and / or absence detection.

SELF CONFIGURATION AND FACTORY DEFAULTS

The SET-DLCM 3 or 5 run through a unique, automatic, simply

intelligent self-configuration process once powered up. This allows a

system to be fully functional 'out of the box' without the need for initial

setup and programming. The self-configuration process is activated

every time the DLCM is powered up, until it has been either programmed

or settings have been changed/modified and stored.

How a system self configures is dependant on various factors.

Such as:-

Whether the SET-DLCM is either a 3 or 5 channel lighting control

module. If occupancy sensors are attached, how many and which input

port they are plugged into.

If light level sensors are attached, how many and which input port they

are plugged into.

If SET-DFP type faceplates are attached.

If more than one SET-DLCM or other 'Output' devices are networked

together.

The self configuration process is dependant on a set of preprogrammed

'Factory Defaults'. These defaults are as follows:-

Occupancy Delay: The SET-DLCM will switch its output channels off

after occupancy ceases. Time delay is 10 minutes by default.

Presence/Absence: The SET-DLCM's can operate as either a presence

or absence detection system. In presence detection mode the lighting

will automatically switch on when someone enters an area where there

are occupancy detectors. In absence mode the lighting will only switch

on when someone operates a switch or scene button on a faceplate. The

lighting can also be manually turned off by the same switch or by the

'Off' button on a faceplate. By default, presence mode is set to 'On'.

BASIC USER GUIDE

SET-DLCM3,5 (A,D)

Dimming Protocols: SET-DLCM3-D and SET-DLCM5-D outputs are

DSI (default). SET-DLCM3-A and SET-DLCM5-A outputs are 1-10v

Analogue.

Dimming Channels: Configure depending on which sensor inputs

light level sensors are plugged into. (See 'Channel Self -Configuration

Table on page 3).

Network Control: When multiple 'Output' devices are networked

(connected) together, how they configure will be dependant on

whether each output device has its own sensors or not. If sensors are

connected to only one output device ALL other output devices on that

network will mirror the output device with the sensors directly

connected to it. If sensor(s) are connected to multiple output devices,

then ALL output devices will operate independently for occupancy

and light level.

Please note: ALL commands and triggers from faceplates or switches

are broadcast across the network and ALL output devices will

respond.

Scenes: When a faceplate is on a system, scenes can be selected

by operating a 'Scene' button on the faceplate. If a light level sensor

is also on the system, the default 'Scenes' will be as follows:-

Scene 1 = Automatic (Daylight linked). Output Level = High

Scene 2 = Automatic (Daylight linked). Output Level = Low

Scene 3 = Manual (Fixed Output). Output Level = High

Scene 4 = Manual (Fixed Output). Output Level = Low

If a faceplate is fitted without any light level sensors, then Scene 1 &

2 are as per scenes 3 & 4 above.

Manually Changing Light Levels: It is possible to manually adjust

light levels temporarily for your convenience by using the 'Raise' or

1 of 4

Unique automatic, simply intelligent self-configuration -

detects sensors and configures itself accordingly.

Programmable - allows the flexibility of re-configuration for

any future changes to the controlled area's use.

Standalone or multiple, fully networked systems using

RS485 networking. Fully scalable.

Override facility.

Emergency Lighting test facility.

Easy integration with BMS (Building Management) and AV

(Audio/Visual) systems.