DynaColor W series Beknopte handleiding
Blader online of download pdf Beknopte handleiding voor {categorie_naam} DynaColor W series. DynaColor W series 2 pagina's. Full hd multiple streams micro dome ip camera
Ook voor DynaColor W series: Beknopte handleiding (2 pagina's)
Pagina afdrukken
The Quick Guide is for quick installing and connecting the Full HD Multiple Streams Micro Box IP Camera (PoE). For
details, please refer to the User's Manual of the IP Camera.
Camera Rear Panel
No.
Connector
1
PoE NETWORK
2
Network LEDs
3
DC 12V Connector
4
Alarm I/O
5
microSD Card Slot
6
Default Button
IP Camera Installation
Please follow the instructions below to complete IP Camera installation.
Power up the Camera
To power up the IP Camera, please plug the camera's DC 12V cable into the power outlet. Alternatively, connect the
Ethernet cable to the camera's PoE port and plug the other end of the cable into a PoE switch.
NOTE: If PoE is used, make sure Power Sourcing Equipment (PSE) is in used in the network.
Ethernet Cable Connection
Connect one end of the CAT5 Ethernet cable to the PoE Network Connector of the IP Camera, and the other end of
the cable to the network switch or PC.
NOTE: In some cases, Ethernet crossover cable might be needed when connecting the IP Camera directly to
the PC.
Full HD Multiple Streams Micro Box IP Camera (PoE) Quick Guide
Definition
For Ethernet Cable and PSE connection
Network connection and activity indication
For Power connection
1
Alarm Input −
2
Alarm Input +
3
Alarm Output −
4
Alarm Output +
For videos and snapshots storage
Press the button with a proper tool to reset the system.
NOTE: Check the status of the link indicator and activity indicator LEDs. If the LEDs are unlit, please check
the LAN connection.
Green Link Light indicates good network connection.
Orange Activity Light flashes for network activity indication.
Before Login to the IP Camera
A client program will be automatically installed to the PC when connecting to the IP Camera. Before logging in to the
IP Camera, please ensure downloading the ActiveX control is allowed by either changing the ActiveX controls and
plug-ins or setting Internet's security level to default. For further details, please refer to the User's Manual of the IP
Camera.
ActiveX Controls and Plug-ins Settings
Step 1: Start the Internet Explorer (IE).
Step 2: Select <Tools> from the main menu of the
browser. Then click <Internet Options>.
Step 3: Click the <Security> tab and select "Internet",
and click <Custom level> to change ActiveX
settings.
Step 4: Set "ActiveX controls and plug-ins" items to
<Prompt> or <Enable>.
IP Camera Login
The IP Camera's default IP address is: 192.168.0.250. Therefore, to access the IP Camera for the first time, set the
PC's IP address as: 192.168.0.XXX; for example:
IP Address: 192.168.0.100
Subnet Mask: 255.255.255.0
Login ID and Password
Key in the IP Camera's IP address in the URL bar of the Web browser window and press "Enter".
Enter the default user name (Admin) and password (1234) in the prompt request dialogue. Note that user name is
case sensitive.
Install the ActiveX Control
After connecting to the IP Camera, the request for installing the ActiveX control will appear just below the URL bar.
Right click on the information bar, and click "Install ActiveX Control..." to permit ActiveX control installation.
In the pop-up security warning window, click "Install" to start downloading DC Viewer software.
Click "Finish" after DC Viewer installation is complete.
Internet Security Level
Step 1: Start the IE.
Step 2: Select <Tools> from the main menu of the
browser. Then click <Internet Options>.
Step 3: Click the <Security> tab and select "Internet."
Step 4: Down the page, click "Default Level" and click
"OK" to confirm the setting. Close the browser
window, and open a new one later for
accessing the IP Camera.