HiB 78700000 Snelstarthandleiding
Blader online of download pdf Snelstarthandleiding voor {categorie_naam} HiB 78700000. HiB 78700000 2 pagina's.
Ook voor HiB 78700000: Snelstarthandleiding (2 pagina's), Handmatig (2 pagina's), Handmatig (2 pagina's)
Pagina afdrukken
This product is IP44 rated and is suitable for installation in
&
zones:
2
Outside Zone
All installations must comply with guidelines which are based on a zonal
concept. The diagram above illustrates this concept and must be followed
to ensure the safe installation of electrical appliances in the bathroom.
These regulations apply to domestic installations only. Installations must be
made in accordance with the current IEE wiring regulations and relevant
building regulations. HiB recommends that all electrical bathroom
products should only be fitted by a suitably qualified, Part P registered
electrician.
Installation
1. Position the mirror in a suitable location (according to the zonal
diagram - Fig. 1), ensuring that the domestic electrical mains
supply is within reach of the electrical entry point of the product.
2. Carefully mark the position of the mirror using a soft pencil
ensuring it is level. Remove the mirror and mark the mounting
points. Please ensure that all marked mounting points
accurately match up with the fixing points on the mirror.
3. Using a suitable drill bit, drill holes in the marked positions to a
suitable depth. If drilling through tile, use a ceramic drill bit.
4. Insert wall plugs level with the surface of the wall. If fitting to a tiled
surface, wall plugs should be inserted below the tile surface to
avoid cracking. NB. For plasterboard walls, specialist fixings should
be purchased, available from any DIY or hardware store.
5. Screw supplied fixings into wall plugs.
6. Ensure the domestic electrical mains supply to which the
mirror is being connected is turned off. Connect the domestic
mains supply to the terminal box according to the wiring diagram
(Fig. B) overleaf.
7. Hang the mirror in position.
8. Switch the domestic electrical mains supply for the mirror back on.
NB. LED Mirrors with charging socket only; On first use of the charging
socket, there may be resistance when inserting the plug. Make sure
that the mirror is held firmly so that it is not pushed off the wall. After a
few uses, resistance will ease and the socket will function as normal.
WEEE compliance
Must not be mixed with general household waste
T:
+44 (0)20 8441 0352
F:
+44 (0)20 8441 0219
Building 3, North London Business Park, Oakleigh Road South, New Southgate, London. N11 1GN
©HiB Copyright: No part of this document may be reprinted or duplicated without HiB consent. All sizes and measurements are approximate, but we do try and make sure they are as accurate as possible. In the
interest of continuous product development, HiB reserves the right to alter specifications as necessary. E & OE.
Illuminated Mirrors
Globe 45
Globe 60
Globe 120
Vega 40
Vega 60
Vega 120
Alpine 60
Alpine 100
Arena 120
(Fig. 1)
Thank you for purchasing this HiB product.
Please read through these instructions carefully and refer back to them
during installation to ensure that your product is fitted safely and that it
retains its high quality finish.
Please retain this leaflet for future reference.
Before installation, ensure the domestic electrical mains supply to
which the mirror is to be connected is turned off. Before drilling,
ensure that there are no hidden cables or pipes in the wall.
Mounting Points Diagram (Fig. A)
Operation Instructions
Vega/Alpine/ Arena - To turn illumination on or off, press the touch
sensor. To cycle through warm to cool colour temperature, press and
hold the touch sensor - release when the desired colour temperature
has been reached. Heated Pad is only on when mirror is illuminated.
Globe - To turn illumination on or off, wave hand past the sensor on
the side/bottom of the mirror. To alter the colour temperature, hold
your hand over the sensor, remove hand when the desired colour
temperature has been reached. Heated Pad is only on when mirror is
illuminated.
NB. Globe mirrors must be installed with a minimum distance of 150mm
between the infra-red sensor switch and any adjacent wall or object to
ensure correct operation of the sensor.
E:
hib.co.uk
Art No. 78400000
/ Globe 50
Art No. 78600000
/ Globe 90
Art No. 78700000
/ Globe 140
Art No. 78749000
/ Vega 50
Art No. 78751000
/ Vega 80
Art No. 78748000
/
Alpine 50
Art No. 78754000
/ Alpine 80
Art No. 78756000
/ Arena 80
Art No. 79531200
REAR VIEW
mounting points
Note: Globe / Arena are dual orientation. Alpine and Vega are fixed
orientation.
FI#01 017 R181017
Art No. 78500000
Art No. 78610000
Art No. 78710000
Art No. 78750000
Art No. 78752000
Art No. 78753000
Art No. 78755000
Art No.79530800
Ver No.
2.0 Jan 2019