GREAT PLANES Riot 3D Gebruiksaanwijzing - Pagina 3

Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} GREAT PLANES Riot 3D. GREAT PLANES Riot 3D 20 pagina's.

Pagina afdrukken

5. You must correctly install all R/C and other components so

that the model operates correctly on the ground and in the air.

6. You must check the operation of the model before every

flight to insure that all equipment is operating and that the

model has remained structurally sound. Be sure to check

clevises or other connectors often and replace them if they

show any signs of wear or fatigue.

7. If you are not an experienced pilot or have not flown this

type of model before, we recommend that you get the

assistance of an experienced pilot in your R/C club for your

first flights. If you're not a member of a club, your local hobby

shop has information about clubs in your area whose

membership includes experienced pilots.

8. While this kit has been flight tested to exceed normal use,

if the plane will be used for extremely high-stress flying,

such as racing, or if a motor larger than one in the

recommended range is used, the modeler is responsible for

taking steps to reinforce the high-stress points and/or

substituting hardware more suitable for the increased stress.

We, as the kit manufacturer, provide you with a top quality,

thoroughly tested kit and instructions, but ultimately the

quality and flyability of your finished model depends on

how you build it; therefore, we cannot in any way

guarantee the performance of your completed model, and

no representations are expressed or implied as to the

performance or safety of your completed model.

Remember: Take your time and follow the instructions to

end up with a well-built model that is straight and true.

LITHIUM BATTERY HANDLING & USAGE

WARNING!! Failure to follow all instructions could cause

permanent damage to the battery and its surroundings, and

cause bodily harm!

• ONLY use a LiPo approved charger. NEVER use a

NiCd/NiMH peak charger!

• NEVER charge in excess of 4.20V per cell.

• ONLY charge through the "charge" lead. NEVER charge

through the "discharge" lead.

• NEVER charge at currents greater than 1C.

• ALWAYS set charger's output volts to match battery volts.

• ALWAYS charge in a fireproof location.

• NEVER trickle charge.

• NEVER allow the battery temperature to exceed 150° F [65° C].

• NEVER disassemble or modify pack wiring in any way or

puncture cells.

• NEVER discharge below 2.5V per cell.

• NEVER place on combustible materials or leave

unattended during charge or discharge.

• ALWAYS KEEP OUT OF REACH OF CHILDREN.

RADIO EQUIPMENT

•

4-channel radio with 3 micro servos such as the Futaba

S3110M with micro plugs (FUTM0702)

•

R124F Micro Receiver (FUTL0438 for Low Band,

FUTL0439 for high band) with single conversion crystal

(FUTL62**) ** selects the channel for your receiver. For

example, if you wish to order a channel 35 crystal, you

would order FUTL6235

•

8A Micro Brushless ESC, such as Silver Series 8A

Brushless (GPMM1800)

•

RIMFIRE

28-22-1380kV Brushless Out-runner

™

Motor (GPMG4505)

•

APC 8x3.8 Slo-Flyer prop (APCQ5000)

•

350-640mAh 3-cell LiPo battery (GPMP0801 – 350mAh

3-cell, GPMP0805 – 640mAh 3-cell)

ADDITIONAL ITEMS REQUIRED

Adhesives & Building Supplies

This is the list of adhesives and building supplies that are

required to finish the Riot 3D ARF.

❏

Great Planes Pro

™

❏

Great Planes Pro medium CA (GPMR6008)

❏

Hobbico

builder's triangle (HCAR0480)

❏

Hobbico hobby knife (HCAR0100)

❏

#11 Blades for hobby knife (HCAR0211)

❏

Top Flite

panel line pen (TOPQ2510)

❏

Drill bits: 1/16" [1.6mm], 3/16" [4.8mm]

❏

1/2" [13mm] Double-sided foam mounting tape (GPMQ4440)

❏

1" [25mm] Double-sided foam mounting tape (GPMQ4442)

Optional Supplies & Tools

Here is a list of optional tools mentioned in the manual that

will help you build the Riot 3D ARF.

❏

Hobbico covering iron (HCAR8000)

❏

21st Century

trim seal iron (COVR2750)

❏

Hobbico heat gun (HCAR7000)

❏

Curved-tip canopy scissors for trimming plastic

parts (HCAR0667)

❏

4 oz. [113g] Aerosol CA activator (GPMR634)

❏

Stick-on segmented lead weights (GPMQ4485)

❏

Small T-pins (100, HCAR5100)

❏

2 oz. [57g] Spray CA activator (GPMR6035)

❏

R/C-56 canopy glue (JOZR5007)

❏

CA applicator tips (HCAR3780)

❏

CA debonder (GPMR6039)

❏

Hook & loop material (1" x 6" [25 x 150mm], GPMQ4480)

❏

AccuThrow

™

deflection gauge (GPMR2405)

❏

Precision Magnetic Prop Balancer (TOPQ5700)

thin CA (GPMR6002)