AFG 2.0AS Assembly and Montage- en gebruikershandleiding - Pagina 5
Blader online of download pdf Montage- en gebruikershandleiding voor {categorie_naam} AFG 2.0AS Assembly and. AFG 2.0AS Assembly and 15 pagina's. Afg series
Ook voor AFG 2.0AS Assembly and: Montage- en gebruikershandleiding (16 pagina's)
Pagina afdrukken
AS SE MB LY ST EP 2
HARDWARE BAG 2 CONTENTS :
BOLT (B)
95 mm
Qty: 4
NYLON
NUT (E)
Qty: 6
ARC WASHER (D)
ARC WASHER (D)
BOLT (F)
LARGE
"O" RING
CENTER
SUPPORT FRAME
SEAT
WELDMENT SET
SEAT
ADJUSTMENT
PIN
2.0AS_Rev.1.5.indd 8-9
A
Open HARDWARE BAG 2.
ARC WASHER (D)
B
Slide LARGE "O" RING
Qty: 12
onto CENTER SUPPORT
FRAME as shown in
LARGE "O" RING
BOLT (F)
diagram.
90 mm
Qty: 1
Qty: 2
C
Attach UPPER PULLEY
ASSEMBLY to CENTER
SUPPORT FRAME using
4 BOLTS (F) and 4 ARC
NYLON NUT (E)
WASHERS (D) and 2
NYLON NUTS (E). Tighten
this hardware.
UPPER PULLEY
ASSEMBLY
D
Attach UPPER PULLEY
NUT (E)
ASSEMBLY to RIGHT
ARC WASHER (D)
MAIN SUPPORT FRAME
BOLT (A)
using 2 BOLTS (B), 4
ARC WASHERS (D) and 2
LEFT SUPPORT
NYLON NUTS (E).
FRAME
E
Attach UPPER PULLEY
RIGHT
SUPPORT
ASSEMBLY to LEFT
FRAME
SUPPORT FRAME using
2 BOLTS (B), 4 ARC
WASHERS (D), and 2
NYLON NUTS (E).
F
Install SEAT WELDMENT
SET onto posts on
CENTER SUPPORT FRAME
as shown in diagram, and
insert SEAT SAFETY PIN.
G
Install SEAT ADjUSTMENT
PIN into SEAT WELDMENT
SEAT SAFETY PIN
SET as shown in
diagram. (Fully thread
into SEAT WELDMENT
SET after SEAT BOTTOM
ADjUSTMENT BAR is
installed.)
ASSEMBLY STEP
HARDWARE BAG CONTENTS :
FLAT
NYLON
BOLT (F)
WASHER (C)
NUT (E)
25 mm
Qty: 10
Qty: 2
Qty: 2
BOLT (H)
FLAT
20 mm
WASHER (I)
Qty: 4
Qty: 2
STEP -B: INSTALLING THE STOPPER:
CENTER
RADIAL ARM ASSEMBLY
SUPPORT
STOPPER
FRAME
LEFT
CONNECTION
FLAT WASHER (C)
TUBE
NYLON NUT (E)
NYLON NUT (K)
NYLON NUT (E)
CENTER
CONNECTION
TUBE
BOLT (J)
BOLT (J)
LEG ROLLER
BOLT (G)
FLAT WASHER (I)
SUPPORT TUBE
A
Open HARDWARE BAG .
B
Remove STOPPER from front side of RADIAL ARM ASSEMBLY and reinstall on back side.
Tighten both STOPPERS.
C
Attach RADIAL ARM ASSEMBLY to CENTER SUPPORT FRAME using 2 BOLTS (F), 2 LOCK
WASHERS (L) and 2 FLAT WASHERS (C). Tighten this hardware.
D
Attach RIGHT SIDE CONNECTION TUBE to SEAT WELDMENT SET and to LOWER
CONNECTION TUBE using 2 BOLTS (H) and 2 FLAT WASHERS (C), as shown in diagram.
E
Repeat on left side.
F
Attach CENTER CONNECTION TUBE to SEAT WELDMENT SET and to LOWER CONNECTION
TUBE using 2 BOLTS (j), 4 FLAT WASHERS (C) and 2 NYLON NUTS (E).
G
Attach LEG ROLLER SUPPORT TUBE to LOWER CONNECTION TUBE using 1 BOLT (G), 2
FLAT WASHERS (I) and 1 NYLON NUT (K). Tighten all hardware in Step 3.
BOLT (G)
NYLON
92 mm
NUT (K)
Qty: 1
Qty: 1
BOLT (J)
LOCK
83 mm
WASHER (L)
Qty: 2
Qty: 2
FLAT
LOCK
WASHER (C)
WASHER (L)
BOLT (F)
RADIAL ARM
ASSEMBLY
FLAT WASHERS (C)
BOLT (H)
RIGHT CONNECTION TUBE
LOWER
CONNECTION TUBE
9/23/08 10:14:19 AM