ADEMCO 5816TEMP Installatie-instructies

Blader online of download pdf Installatie-instructies voor {categorie_naam} ADEMCO 5816TEMP. ADEMCO 5816TEMP 2 pagina's. Low temperature transmitter

Pagina afdrukken

GENERAL

The 5816TEMP Low Temperature Transmitter contains a low temperature detector that transmits a message

INFORMATION

(alarm or trouble depending on the installer's programming entry) to a 5800 wireless receiver that is connected

to a QED control panel. The message is sent when the Temperature Sensor thermostat temperature reaches

+45°F ± 5°F (+4°C ± 3°C). The device resets after a temperature rise of about 9°F (5°C) for 5 minutes. At that

time, a restore message is sent to the receiver and the QED control panel.

ENROLLING THE

Each 5816TEMP is permanently assigned its own serial number. The QED control panel is required to "enroll"

TRANSMITTER

the transmitter's serial number prior to the transmitter's usage.

SERIAL NUMBER

Refer to the QED control panel's Installation Instructions for general information on the "enrolling" procedure.

The information given herein is specific to the 5816TEMP.

1. Place a battery in the battery holder, as described later in BATTERY INSTALLATION/REPLACEMENT

2. While in the zone programming mode, as described in the QED control panel's instructions, program this

NOTE: The polarity of the magnet must be correct; if the device is not enrolled as indicated on the keypad,

MOUNTING

For proper orientation of the unit in relation to its wall mounting plate and the loop wiring, read all of this section

before installing the unit.

Installing within close proximity to iron, steel and magnetic materials will affect the activation

temperature. Do not mount the unit within 1 ft. of these types of materials.

The description that follows assumes that the unit will be mounted as shown in the diagrams. The unit may,

however, be installed in any direction, as long as the relationship of the unit to its mounting plate is maintained.

Although two holes are provided in the unit that would permit mounting directly to a surface (holes 'A' in

Diagram 2), it is recommended that the mounting plate be used, as described below, for ease in removing the

unit for servicing should it become necessary.

Before mounting the transmitter permanently, conduct Go/No Go tests (see QED control's instructions) to

verify adequate signal strength and reorient or relocate the transmitter if necessary. When a satisfactory

location is found, remove the battery and proceed with installation.

1. Disengage the supplied wall mounting plate from the unit by inserting the blade of a small screwdriver

2. Install the mounting plate, with its case holding posts pointing up, in the location selected as described in

3. Remove the transmitter's cover by inserting the flat blade of a small screwdriver into the closed pry-off

4. Attach the case back to the mounting plate by sliding the keyhole slots in the case back down onto the

5. Install the battery as described in BATTERY INSTALLATION procedure on the next page.

6. Replace unit's cover by engaging the case holding posts along the edge and snap shut.

HOLDING

POSTS (2)

PLATE

MOUNTING

HOLES (2)

CASE LOCKING TAB

Diagram 1. MOUNTING PLATE

INSTALLATION INSTRUCTIONS

For use with QED control panels ONLY!

and as shown in Diagram 2. Observe polarity!

device as the input type, "supervised RF," and enter "1" as its loop number. Transmit from the device

(press the tamper switch, move the magnet, etc.).

reverse the magnet's direction and redo step 2.

into the locking tab release window (Diag. 2) and pressing it against the locking tab (Diag. 1) while sliding

the plate downward along the case back.

the QED control panel's Installation Instructions. Use the screws supplied. The word TOP is molded along

the upper edge of the plate.

slot at the end of the unit farthest from the cover's decorative ribs, and twisting the blade.

mounting plate's case holding posts.

CASE

ALIGNMENT

GUIDE STRIP

LOW TEMPERATURE TRANSMITTER

COVER PRY-OFF POINT

HOLES "A" (2)

(SEE TEXT)

BATTERY

ANTENNA

–

COVER

TAMPER

SWITCH

COVER

HOLDING

HOOKS (2)

LOCKING TAB

RELEASE WINDOW

FOR ENROLLING, BRING

MAGNET PARALLEL TO

SENSOR AND REMOVE.

DO THIS TWICE.

Diagram 2. No. 5816TEMP (Shown With Cover Removed)

TEMPERATURE

SENSOR

EXPLODED

VIEW

MAGNET

@ @ @ @ @ @ @ @ e ?

@ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @

@ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e

@ @ @ @ @ @ @ @ e ?

@ @ h ?

@ @ @ @ @ @ @ @

@ @ @ @

@ @ h ?

@ @ @ @

@ @ h ?

@ @

MAGNET

@ @

@ @ g

? @ @

@ @ g

? @ @

@ @ g

? @ @

@ @ @ @ @ @ @ @

? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @

? @ @ @ @ @ @ @ @

N7627V2 5/98

5816TEMP