ADEMCO 6137 Installatiehandleiding - Pagina 2

Blader online of download pdf Installatiehandleiding voor {categorie_naam} ADEMCO 6137. ADEMCO 6137 2 pagina's. Remote keypads
Ook voor ADEMCO 6137: Gebruikershandleiding (9 pagina's), Beknopte handleiding (3 pagina's), Installatiehandleiding (2 pagina's), Installatiehandleiding (2 pagina's)

Pagina afdrukken

Remove the case back by pushing down two "snaps" located

under the arrows in diagram on previous page .

2. Route wiring from the control panel through the opening in the

case back.

3. Mount the case back to a wall or electrical box.

4. Plug the supplied flying lead connector into the keypad PC

board and splice the panel wiring to it, or wire directly to the

terminal block on the PC board (wire colors are marked next to

Use the WIRING TABLE that matches

terminals).

the way the PCB is marked on the keypad your

connecting.

5. Reattach the keypad to its case back.

6. Remove the clear protective films from the LCD display and

keypad labels.

SETTING THE KEYPAD ADDRESS

The keypad can be set for an address of 0-31 (the keypad will not

accept entries greater than 31), which is stored in EEROM memory.

The keypad's default address is 31 (non-addressable mode–some

early versions of 6139/6139R default to 11).

To change the keypad's address, do the following:

1. Enter address mode: Power up (plug in) the keypad. Within 60

seconds of power-up, press and hold down the [1] and [3] keys at

the same time for 3 seconds. (If unable to enter address mode,

power up and try again.)

The current keypad address will be displayed, and the cursor

will be under the "tens" digit. If 10 seconds have passed with no

key entry, the keypad automatically exits address mode. You

must power down, power up and start address mode again.

NOTE: The keypad will not enter address mode if the panel to

which it is connected is in programming mode.

2. Set the current address to "00": Press [0] to clear the current

"tens" digit. The cursor will move to the "ones" digit position.

Press [0] to clear the current "ones" digit. The cursor will move

back to the "tens" digit position.

3. Enter the keypad's address: Enter the proper "tens" digit of the

keypad's address.

The cursor will move to the "ones" digit

position. Enter the proper "ones" digit of the keypad's address.

Note that address "31" sets the keypad to non-addressable

mode.

4. Exit address mode:

Press [✱] to save the displayed address and exit address mode.

REFER TO INSTALLATION INSTRUCTIONS FOR THE CONTROL PANEL FOR DETAILS ON LIMITATIONS OF THE ENTIRE ALARM SYSTEM.

Alarm Device Manufacturing Company, a Division of Pittway Corporation, and its divisions, subsidiaries and affiliates ("Seller"), 165 Eileen Way, Syosset, New York 11791, warrants its products

to be in conformance with its own plans and specifications and to be free from defects in materials and workmanship under normal use and service for 24 months from the date stamp control on

the product or, for products not having an Ademco date stamp, for 12 months from date of original purchase unless the installation instructions or catalog sets forth a shorter period, in which

case the shorter period shall apply. Seller's obligation shall be limited to repairing or replacing, at its option, free of charge for materials or labor, any product which is proved not in compliance

with Seller's specifications or proves defective in materials or workmanship under normal use and service. Seller shall have no obligation under this Limited Warranty or otherwise if the product

is altered or improperly repaired or serviced by anyone other than Ademco factory service. For warranty service, return product transportation prepaid, to Ademco Factory Service, 165 Eileen

Way, Syosset, New York 11791.

THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE

DESCRIPTION ON THE FACE HEREOF. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR

ANY OTHER WARRANTY, EXPRESS OR IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER'S

OWN NEGLIGENCE OR FAULT.

Seller does not represent that the products it sells may not be compromised or circumvented; that the products will prevent any personal injury or property loss by burglary, robbery, fire or oth-

erwise; or that the products will in all cases provide adequate warning or protection. Customer understands that a properly installed and maintained alarm may only reduce the risk of a bur-

glary, robbery, fire or other events occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as

a result. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT

FAILED TO GIVE WARNING. HOWEVER, IF SELLER IS HELD LIABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED

WARRANTY OR OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN, SELLER'S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE

PRODUCT, WHICH SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER. This warranty replaces any previous warranties and is the only warranty made by Seller on

this product. No increase or alteration, written or verbal, of the obligations of this Limited Warranty is authorized.

¬19l

N6752V9 2/03

VIEWING THE KEYPAD ADDRESS

Press and hold down the [1] and [3] keys at the same time for about

3 seconds.

allowed. Press any key to exit or wait 10 seconds to automatically

exit viewing mode.

WIRING TABLES

Wiring:

(all

Keypads)

SPECIFICATIONS

Physical:

6128: ...................... 4-3/4"H x 5-3/4"W x 1"D

6137/6137R: ............ 4-3/4"H x 6-1/4"W x 1"D

6138/6139/6139R: ... 4-3/4"H x 6-3/4"W x 1-1/4"D

Current:

6128: ..............45mA sounder on, 30mA standby, alarm sounder off.

6137/6137R: ..85mA (ARMED LED lit, LCD backlight and sounder

6139/6139R: ...100mA (ARMED LED lit, LCD backlight and

Displays:

6138: ..............1 x 16 alpha-numeric supertwist LCD, backlit.

6139,6139R: ...2 x 16 alpha-numeric supertwist LCD, backlit.

6128, 6137:.....Fixed-Word LCD (6137 backlit).

Sounder:.........Piezo-electric (fire alarm is loud, pulsing single tone;

(all Keypads) burglary alarm is loud, continuous, dual tone).

ADEMCO LIMITED WARRANTY

The current address is displayed.

Color

Function

Red

+12VDC

Black

Ground

Blue

If present, not used.

Green

Data to control panel.

Yellow

Data from control panel.

Keypad

Control Panel

Data Out

Data In

GND

Aux Pwr

+12VDC

+ Aux Pwr

Data In

Data Out

on), reduces to 40mA when panel is operating in

standby mode (backlight off).

sounder on), reduces to 40mA when panel is

operating in standby mode (backlight off).

165 Eileen Way, Syosset, New York 11791

1993 PITTWAY CORPORATION

No key entry is

Color

Green

Black

Red

Yellow