2gig Technologies 2GIG BRDG1 900 Installatie-instructies - Pagina 2

Blader online of download pdf Installatie-instructies voor {categorie_naam} 2gig Technologies 2GIG BRDG1 900. 2gig Technologies 2GIG BRDG1 900 4 pagina's. Bridge ip communicator

Pagina afdrukken

If the 900MHz LED illuminates in GREEN (the lower LED),

NOTE:

verify that the network cable is not connected to the

Go!Bridge. If the cable is disconnected and it is still illuminated

GREEN, use the end of an open paperclip to press and release

the recessed Reset button. The button is located inside the

small hole on the port side of the Go!Bridge, directly above

the Ethernet port. This restores the factory settings. See Figure

3 Go!Bridge Rear View—Ports and Recessed Reset Button.

Figure 3 Go!Bridge Rear View

A Recessed Reset Button

B Ethernet Port

Power Supply Port

After the Go!Bridge is powered ON, continue with Programming

the Go!Bridge into the Control Panel.

Programming the Go!Bridge into the Control

Panel

Use these steps to place the control panel and Go!Bridge in learning

mode. This gives the control panel the ability to learn the network

settings transmitted by the Go!Bridge.

NOTE:

To scroll between op ons on the control panel, tap the ←

and → arrows. To move to the previous or next prompt tap the

↑ and ↓ arrows.

Connect an Ethernet cable (not included) to the router and

Go!Bridge. Do not plug the cable into the uplink port.

IMPORTANT:

For compliance with UL 1023: Household Burglar‐

Alarm System Units, the Go!Bridge must be installed in the

same room as the Internet modem or router.

Ensure the control panel is powered ON. Then tap the Home

button.

Tap the system logo in the lower‐right corner of the control panel

Home screen.

At the Enter Your Code screen, enter the four (4)‐digit master

installer code to go to the Installer Toolbox (1 of 2) screen.

At the Installer Toolbox (1 of 2) screen, tap System Configuration.

At the Q1: Select RF Sensor # (01 to 48) screen, tap Go To.

At the Enter Question Number (2 Digits) screen, enter 92.

At Q92 Select Network Device (0 to 1), tap → to scroll to (1)

Go!Bridge. Then tap ↓.

At Q: Network Device ID (Read Only), tap Learn. This gives the

panel the ability to discover the read‐only network device ID

transmitted by the Go!Bridge.

At the Pair with Xcvr Device screen, the "initiating learning

process" message appears.

On the Go!Bridge, press and release the Learn button (this is the

small, black plastic button on the LED side of the Go!Bridge below

the 900MHz LED). This transmits the device ID to the Control

Panel.

When the "learn operation succeeded" message appears and the

panel displays the Type (Go!Bridge) and ID#, the Go!Bridge and

panel are linked. The 900MHz LED on the Go!Bridge also flashes

GREEN.

—

Ports and Recessed Reset Button

At the Pair with Xcvr Device screen, tap OK. Then tap ↓ to

continue with At the Q: Select Port # (1 to 8) screen, enter the port

number for the third‐party monitoring services' server. Then tap ↓.

below.

At the Q: Select Port # (1 to 8) screen, enter the port number for

the third‐party monitoring services' server. Then tap ↓.

At Q: Used (0 to 1), tap → to select one (1) of these options:

• (0) Disabled (Recommended). This is the default setting. Most

users will keep this port disabled. Then tap Next and skip to

step 14.

• (1) Enabled. Then tap ↓. At the Q: Enter Port Value (0‐65535)

screen, tap ↓ to accept the default port value. Next, at the Q:

Enter Port Forward IP Address screen, tap ↓ to accept the

address configured by the provider. You can configure up to

eight (8) ports. If you are finished configuring ports, tap Next.

At the Summary of Network Device screen, tap ↓. Verify the list

of port numbers and forward IP addresses appears as

programmed. Then tap Skip.

At Q93 Enter Broadband Network Failure Time (1 to 255), enter

the desired number of minutes that must pass before a network

failure triggers the Control Panel to issue a trouble alert. The

default value is 30 minutes. Then tap ↓.

NOTE:

A trouble alert consists of an audible beep and the Control

Panel's Home screen displays a trouble message.

At Q94 Select Broadband Network Failure Report (0 or 1), tap →

to select whether or not to report the broadband network failure

to the monitoring service:

• (1) Enabled. This is the default setting. Network failures are

reported to monitoring service.

• (0) Disabled. Network failures are not reported.

Tap End.

At the Summary of System Configuration screen, verify the

settings. Then tap Save Changes.

Tap Exit to the close the System Configuration screen.

LED Indicators

The table Verifying the Settings

Network LED

Globe Icon

Solid GREEN

Indicates the presence of an external network connection.

Flashing GREEN Network cable is plugged in and IP address is actively being

assigned.

Solid RED

Network cable unplugged.

900 MHz LED

Icon Labeled "900MHz"

Solid GREEN

Linked and communicating with the Control Panel.

Flashing GREEN Linked to the Control Panel. Communication issues exist.

Solid RED

Not linked to the Control Panel, turns solid after a device reset.

Flashing RED

Not linked to the Control Panel.

In addition to verifying the settings after configuring the Go!Bridge,

you can also verify the settings at any time as follows:

At the Control Panel's Home screen, tap Security.

Tap Menu.

Tap Toolbox.

In the Enter Your Code to Access the Toolbox screen, enter the

master user code.

Tap → to scroll to the Toolbox (3 of 3) screen. Then tap Go!Bridge

Status.