Galanz DWIUK001 Gebruiksaanwijzing - Pagina 4
Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Galanz DWIUK001. Galanz DWIUK001 13 pagina's.
Pagina afdrukken
Dishwasher Features
7
8
2
4
5
4．Prior to Using for the First Time
Before using your dishwasher for the first time:
A. Set the water softener
B. Pour 500ml of water inside the salt container and then fill with dishwasher salt
C. Fill the rinse aid dispenser
D. Select appropriate detergent
A. Setting the Water Softener
The water softener is designed to remove minerals and salts from the water, which would have a
detrimental or adverse effect on the operation of the appliance. The higher the content of these
minerals and salts, the harder the water is. The softener should be adjusted according to the
hardness of the water in your area. Your local Water Authority can advise you on the hardness of
the water in your area.
Setting
The amount of salt dispensed can be set from H0 to H7.
Salt is not required at the set value H0.
1. Set the value which can be found in the water hardness table.
2. Close the door.
3. Switch on the "Power" switch.
4. Hold down " Delay" button and then press "Programme" button for 5 seconds.The buzzer sounds one time
and H flashes on the digital display .(factory setting is H4)
4
Front View
Front View
1 Upper Basket
1
2 Spray Arms
3 Lower Basket
4 Water Softener
5 Detergent Dispenser
6 Rinse Aid Dispenser
3
7 Cutlery Tray
8 Cup Holder
6
For optional performance
1. Set the value which can be found in the
water hardness table.
2. Close the door.
3. Switch on the power switch.
4. Hold down " Delay " button and press " Programme"
button for 5 seconds.The buzzer rings one
time and H flashes on the digital display
(factory setting is H4)
To change the setting:
1. Press " Delay " button.
Each time the button is pressed, the set value
increasesby one level;when the value of H7 has
been reached, the display jumps back to H0(off).
2. Press " Programme " button. The chosen setting
has now been stored.
B. Loading the Salt into the Softener
Always use salt intended for using with dishwasher.
NOTE: If your model has no water softener, you may skip this section
WATER SOFTENER
The hardness of the water varies from place to place. If hard water is used in the
dishwasher, deposits will form on the dishes and utensils.
The appliance is equipped with a special softener that uses salts specifically
designed to reduce lime and minerals from the water .
The salt container is located beneath the lower basket and should be filled as follows:
Attention!
Only use salt specifically designed for use in dishwashers! All other types of salt not specifically
designed for use in a dishwasher, especially table salt, will damage the water softener. In case of
damages caused by the use of unsuitable salt the manufacturer does not give any warranty nor is
liable for any damages caused.
Only fill with salt just before starting one of the complete washing programmes.
This will prevent any grains of salt or salty water, which may have been spilt, remaining on the
bottom of the machine for any period of time, which may cause corrosion.
After the first wash cycle the control panel light expires.
1
A. Remove the lower basket and then unscrew and remove the cap from the salt container.
B. If you are filling the container for the first time, fill 2/3 of its volume with water (around 500ml).
Water hardness table
Water hardness
Set value on
Mg/L
the machine
Clark
Range
0-8
soft
0-110
H0
9-10
soft
120-140
H1
medium
150-180
11-12
H2
13-15
medium
190-210
H3
220-290
16-20
medium
H4
21-26
hard
300-370
H5
27-38
hard
380-540
H6
39-62
hard
550-890
H7
2
1
2
5