Autonics AFL-H26 Snelstarthandleiding - Pagina 2

Blader online of download pdf Snelstarthandleiding voor {categorie_naam} Autonics AFL-H26. Autonics AFL-H26 3 pagina's. Interface teminal block

Pagina afdrukken

-|Transparent Guide|-

Ordering Information

This is only for reference.

For selecting the specific model, follow the Autonics web site.

AFL

❶ The number of connector pin

20: 20-pin

26: 26-pin

40: 40-pin

50: 50-pin

❷ Connector

No-mark: HIF3BA, XG4A-2031, XG4A-2631

B: HIF3BB

Sold Separately

• I/O cable

Specifications

Model

AFL-H20

The number of

connector pin

The number of

terminal

Terminal type

Screwless

Terminal pitch

5.0 mm

20-pin Omron

Connector for

(XG4A-2031)

controller side

Material

Case, Base: PC

Approval

ᜢ ᜨ

Unit weight

≈ 48.5 g

(packaged)

(≈ 86.2 g)

Model

AFL-H20-LN, AFL-H20-LP

The number of

connector pin

The number of

01)

terminal

Terminal type

Screwless

Terminal pitch

5.0 mm

Connector for

20-pin Omron (XG4A-2031)

controller side

Input logic

NPN / PNP model

Indicator

Power indicator: red, operation indicator: blue

Material

Case, Base: PC

Approval

ᜢ ᜨ

Unit weight

≈ 48.6 g

(packaged)

(≈ 86.3 g)

01) Four terminals among twenty terminals are used for LED power.

02) Eight terminals among fourty terminals are used for LED power or N.C (Not Connectred) terminals.

Basic model: ≤ 125 VDCᜡ, 125 VACᜠ 50/60 Hz

Rated voltage

01)

Indicator equipped model: ≤ 24 VDCᜡ ± 10%

Rated current

≤ 1 A

Insulation

≥ 1,000 MΩ (500 VDCᜡ megger)

resistance

Dielectric

2,700 VACᜠ 50/60 Hz for 1 minute

strength

0.75 mm amplitude at frequency of 10 to 55 Hz (for 1 minute) in each X, Y, Z

Vibration

direction for 2 hours

Vibration

0.75 mm amplitude at frequency of 10 to 55 Hz (for 1 minute) in each X, Y, Z

(malfunction)

direction for 10 minutes

Shock

150 m/s

Shock

100 m/s

(malfunction)

Ambient

-15 to 55 ℃, storage: -25 to 65 ℃

(a non freezing or condensation environment)

temperature

Ambient

35 to 85 %RH, storage: 35 to 85 %RH

humidity

(a non freezing or condensation environment)

Protection

IP20 (IEC standard)

structure

01) When connecting loads to output part, connect loads of same power type. Connecting loads of different power

type may cause safety issues.

Applicable wire

Ø 0.3 to 1.2 mm

- solid

01)

Applicable wire

AWG 22-16 (0.30 to 1.25 mm²)

- stranded

01) 02)

Wire ferrule

connection

≥ 30 N

tensile strength

Stripped length 8 to 10 mm

01) Use the cable of copper conductor in 60 ℃ temperature class.

02) When using the stranded wire, use End Sleeve (wire ferrule).

Wire Ferrule Specifications

• Unit: mm, Use the UL approved wire ferrule.

❶

❷

❸

❹

❸ Indicator

No-mark: no LED

L: LED equipped

❹ Input logic

No-mark: None

N: NPN

P: PNP

AFL-H26

AFL-H40

AFL-H50

Screwless

5.0 mm

26-pin Omron

40-pin Hirose

50-pin Hirose

(XG4A-2631)

(HIF3BA-40PA-

(HIF3BA-50PA-

54DSA)

2.54DSA)

≈ 60 g

≈ 89 g

≈ 110 g

(≈ 89 g)

(≈ 156 g)

(≈ 177 g)

AFL-H40-LN, AFL-H40-LP

02)

Screwless

5.0 mm

40-pin Hirose (HIF3BA-40PA-2.54DSA)

≈ 91 g

(≈ 158 g)

(≈ 15 G) in each X, Y, Z direction for 3 times

(≈ 10 G) in each X, Y, Z direction for 3 times

10 to 12

≤ 4.1

≤ 2.0

Dimensions

• Unit: mm, For the detailed dimensions of the product, follow the Autonics web site.

20-pin

AFL-H50B

26-pin

40-pin

50-pin

Screwless

5.0 mm

Installation

50-pin Hirose

(HIF3BB-50PA-

■ DIN RAIL

2.54DSA)

• Mounting

1. Pull the Rail lock on the rear of the product to the direction ①.

≈ 110 g

2. Hang DIN rail hook on the rear of the product onto DIN rail.

(≈ 177 g)

3. Push the product to the direction ②, and push the Rail lock to the direction ③ to fix

onto the DIN rail.

• Removing

1. Insert a tool such as screwdriver into the hole of Rail lock.

2. Push the toll to the direction ① and pull the Rail lock.

3. Lift bottom of the product to the direction ② and remove the product from DIN rail.

■ Panel

Product with the mounting hole can be installed on panel with screw.

It is recommended to use M4×25 mm of spring washer screws.

If you use flat washer, its diameter should be Ø 8 mm.

Tighten the screw with the tightening torque of 0.7 to 1.0 N·m.

Wiring

• Connecting

Insert the wire ferrule into the terminal hole.

• Removing

1. Put the (-) screwdriver at the groove on the clamp lever

and press it.

2. Pull the cable to disassemble.

2-M4

57.5

2-Ø4.2

72.5

2-Ø4.2

106.5

2-Ø4.5

131.5

102

2-Ø4.5

102

DIN rail hook

DIN rail

Rail lock

①

③

①

②

Rail lock

Mounting hole

35 mm DIN RAIL

②