dbx 160A Gebruiksaanwijzing - Pagina 15

Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} dbx 160A. dbx 160A 20 pagina's. Compressor limiter
Ook voor dbx 160A: Brochure & specificaties (2 pagina's)

Pagina afdrukken

TO RIGHT INPUT

FROM RIGHT OUTPUT

Using External Level Detector Inputs

To control the compressor by signals other than the audio input (via an auxiliary device), connect the auxiliary device's

output to the 160A's DETECTOR INPUT jack, and feed the auxiliary device's input with the same signal fed to the 160A's

INPUT (Figures 4 and 5). This requires a Y-adaptor, unless the input signal has already been split (e.g., some synthesizers

can send the same signal to two outputs).

In certain situations, the auxiliary device may need to be inserted in the signal path, not in the detector path. In such cases,

signal is fed to the input of that device, and also to the DETECTOR INPUT, and the auxiliary device's output is fed to the

160A INPUT (e.g., using a delay line to create "negative" attack times).

Specific System Connections

The 160A has balanced inputs and outputs, and can be used with any line-level device. Some common examples include:

mixing consoles, musical instruments, patch bays, and other signal processors.

Mixing Board

If you wish to compress a particular track of a multitrack recording or one channel of a live performance, connect the 160A

INPUT to the audio source's output jack while the 160A OUTPUT can be directly connected to a line input jack (balanced

or not) or the 160A's INPUT and OUTPUT can be wired to an Insert point. In the latter case, the signals will most likely be

unbalanced .

Note: The amount of compression is directly related to the level of the input signal. However, depending upon your system's setup, it may not always be

crystal clear as to what volume controls in your chain affect input level and which affect output level. If the 160A, in relation to your mixer channel's volume

controls, is "pre-fader" (i.e., the 160A is connected to mixer inserts so that the compression effect occurs before the mixer channel's volume fader), you can

boost or cut the input level by adjusting the source's volume control (e.g., a synthesizer's volume control) and boost the track's output level using the 160A's

OUTPUT GAIN control or the mixer's volume fader (the latter here is great for track fade-outs). If the 160A, is "post fader" (i.e., the 160A is connected to

mixer inserts so that the compression effect occurs after the level set by the mixer channel's volume fader), adjusting the mixer's volume fader changes the

input level and the amount of compression. If you would rather have this volume fader control output, we suggest you set up the compressor directly

between the source and the mixer channel's input. This way, you can use the instrument's volume control to define the input level and amount of compres-

sion and the mixer's volume fader to change only the overall volume of the track.

Musical Instruments (e.g., Electric Guitar, Bass, Keyboards, Electric-Acoustic Instruments)

The output of an electric guitar is sometimes not "hot" enough to drive the 160A's INPUT. When this is the case, you

should use the "PREAMP OUT" of your guitar amp (if so equipped), or the output of some other device that is designed to

accept low-level instrument inputs (including various foot pedal effects, acoustic pickup preamps, and rack mount audio

products, like the dbx 163X, 263X, and 563X). Such sources can be balanced or unbalanced -- this is no problem for the

160A.

Microphones, bass guitars, and electric-acoustic instruments, also typically have low-level outputs. With most setups they

require signal boost to drive the 160A's INPUT. For example, when recording voice directly to a portable tape deck, a mic

preamp placed between the mic and the 160A (which is then fed to one of the recorder's inputs) can boost the signal for the

160A as well as provide a high level signal to the tape deck.

Keyboards, samplers, drum machines and sound modules typically produce a line-level signal and can be connected direct-

ly from the instrument's output to the 160A's INPUT.

"MASTER"

160A

INPUT OUTPUT

STEREO

STRAPPING

Figure 6: Multi-Channel Connections

dbx 160A COMPRESSOR / LIMITER

INPUT OUTPUT

TO LEFT INPUT

FROM LEFT OUTPUT

TRS "STEREO" CABLE

(Shield plus two conductors)

"SLAVE"

160A

STEREO

STRAPPING