ADEO SCREEN TENSIO PSCHP0399 Gebruikershandleiding - Pagina 4

Blader online of download pdf Gebruikershandleiding voor {categorie_naam} ADEO SCREEN TENSIO PSCHP0399. ADEO SCREEN TENSIO PSCHP0399 14 pagina's.

Pagina afdrukken

GENERAL FEATURES:

Screens manufactured by Adeo Screen S.p.a. meet the following standards: 73-23 CEE and 89-336 CEE

Projection curtain made of PVC, without cadmium, fire proof class M1 e M2 (LNE Laboratorie national de mètrologie et d'assais – SME Centre de recherches du Bouchet).

Aluminium case with anti scratch paint, of white colour (other colours available on request)

UNPACK THE SCREEN:

Make sure that the screen has not been damaged during the transport check that all the accessories are inside the screen's packing

PROVISION ACCESSORIES FOR ELECTRIC SCREEN:

-screens with case:

2 mountings for ceiling and 2 for wall installation1

-screens without case: 2 side mountings

-screens with case: screws and plastic knuckle pins to lock the mountings to the screen's case

-screens without case: screws and knuckle pins

-unipolar commutator 10 A, 250 V a.c., with directional arrows.

-commutator box for external wall installation

-owner manual

1 the number of mountings is two for the screen sizes until 300x225 cm and three for bigger sizes.

INSTALLATION:

The screen must be installed using screws and anchors suitable for the type of wall or ceiling onto which the brackets have to be fitted.

IMPORTANT!!! AFTER FITTING THE SCREEN ON THE BRACKETS, IT IS MOST IMPORTANT TO MAKE SURE THE SCREEN IS PERFECTLY HORIZONTAL BEFORE

USING.

EMPLOYMENT

It is suggested to use the screens in indoor rooms with normal condition of temperature (20-25° C) and humidity. The exposition to a temperature of more than 50° C could create

permanent damages to the planarity of the projection curtain, or the fall of it from the roller. Do not leave for long time the screen curtain exposed to the sun light to prevent the

yellowing of it (check that also as a cause of the exposition at the sun light, the screen does not reach the level of temperature above mentioned)

Because the material of which the projection curtain is made of (PVC) has the tendency of electrostatics loading, the excessive presence of dust in the projection room could

create the degrade of the optics qualities of the curtain caused from the deposit of the dust.

Do not force the cloth to come out by hand because this could cause damage to the motor or the detachment of the box containing the attachment brackets.

It is forbidden to block, impede or force the movement of the screen by grabbing on to it or swinging on it, adding or applying any object to the fabric or backdrop or modifying the

structure of the screen since it could damage the winding system with consequent property damage and injury to persons.

If you do not follow the instructions above mentioned, damages caused to the screen are not covered from warranty.

The producer is not responsible for damage to things or persons caused from mistakes in installing or using the products..

CASE: for cleaning the case you can use a soft cloth with eventually a non aggressive detergent.

PROJECTION CURTAIN: use a humid soft cloth with eventually a neutral detergent. After the cleaning it could appens that the curtain loads electrostatics, caused from the

rubbing with the cloth, it is suggested to clean the curtain with a liquid products that avoid the settling of the dust.

The installation is the same for all kind of screens, and it is different only for the presence of the case or not. For the case screen's, depending on the size, two kind of cases are

used as indicated in table below. The screens without case are formed from a roller around which there is the projection curtain rolled up, and two mountings which are needed

to mount the screen on the wall or on the ceiling.

INSTALLATION OF THE SCREENS WITH CASE: (Fig. 2 and 3)

The installation could be made on the wall or on the ceiling as showed in the Fig. 2 and Fig. 3 following

WALL INSTALLATION:

insert the screw 4 into the plate 1 and screw down a little bit the nut 3 leaving 4-5 mm of slack; hook the plate to the case and fix it trough the plastic knuckle pins 2. As shown in

the figures the fixing side with the pins of the plate has to be turned to the back side of the case so the mountings are not visible, giving so a good appearance to the installed

screen. we have to underline that only for installation purposes it is the same if you mount the plate in one side or in the other because the hook's profiles of the case are

perfectly symmetrical. Fix the mountings 5 with expansion dowel which has to be suitable to the type of wall (minimum Ø 8 mm) and fix the plate 1 with mountings 5 by using ring

7 and thumb nut 3.

CEILING INSTALLATION: insert the screw 4 into the plate 1 and screw down a little bit the thumb nut 3 leaving 4-5 mm of slack; hook the plate to the case and fix it trough the

plastic knuckle pins 2. Fix the mountings on the ceiling 6, included in the screen package, with expansion dowel which has to be suitable to the type of wall (minimum Ø 8 mm),

at a distance of 10 - 15 cm from the ends of the case. For the screens with a width of more than 350 cm the third mountings has to be fixed on the centre of the case. Make the

plates run 1 in the profile and positioned them in connection with the L fluting of the mountings 6, Take care of the operation is made until the bottom of the L fitment and then

tight the nut on the mounting (the nut is made with a tightness knurling). fix the plate 1 with mountings 6 by using ring 7 and thumb nut 3.

CEILING INSTALLATION DIRECTLY WITH THE FIXING PLATE

It is possible to install the screen on the ceiling directly with the fixing plate. If you wish the case more close to the ceiling (attention: to make easily this operation it is required a

very good planarity of the ceiling and a perfect alignment of the plates) fix the plates with expansion dowel which has to be suitable to the type of wall (minimum Ø 8 mm), at a

distance of 10 - 15 cm from the ends of the case. For this kind of installation the side of the plate for the fixing pins has to be on the forward side of the screen so it will be easier

to insert the knuckle. Check the alignment of the plates. For this purpose you will need shims as the metal insert included in the package. Pay attention that from the care of this

operation depends the easier way of the following fixing of the case to the plate. For the screens with a size bigger than 350cm the third plate has to be installed in the centre of

the case. Insert the case in the plates with a rotatory movement (snap insert) and run the plastic knuckles that assure the fixing of the case.

INSTALLATION SCREEN WITH SYSTEM EXPRESS: (Fig. 6)

1 fix with suitable expansion dowel (minimum Ø 8 mm), the opposite mountings 8 (is possible the wall or ceiling installing) controlling their levelling;

2) to fix the screen to the stirrups following the fig.6;

FEATURES:

The motor is realised with a tubular asynchronous monophasic runner with the following features:230V, 50 Hz, 90 W, 17 revolutions per minute.

The motor of the screens with case is located in the right side of the screen (on request it is possible to have it on the left) if the screen is without case the motor is located on the

left. It works through a commutator supplied from the producer or through an optional remote control.

ELECTRIC CONNECTIONS:

The electric cabling must respect the CEE regulations. According to the CEI 335-1 norm, you have to install an upstream omnipolar switchgear with a minimum contacts opening

spacing of 3 mm.

Use for driving the screen only the commutator supplied from the producer, or an equivalent model following the instructions of Fig. 4 (if the motor is mounted on the left the

colours of the threads must be inverted, descent =brown, ascent = black).

WARNING: do not never connect two or more motors to the same commutator without a group remote, or two commutator to the same motor.

TROUBLESHOOTING OF THE MOTORISED SYSTEM:

Check the power supply 230 V on the control commutator.

SCREEN'S DESCRIPTION

WARNING AND CAUTION

CLEANING

INSTRUCTIONS FOR THE INSTALLATION

MOTORISED SCREENS (Fig.4)

PROVISION ACCESSORIES FOR TURNSTILE SCREEN:

screens with case

2 mountings for ceiling and 2 for wall

installation1.

screens with case: screws and plastic knuckle pins to lock the

mountings to the screen's case

articulated joint rod

owner manual