Gallien-Krueger MicroBass-III Series Gebruikershandleiding - Pagina 3
Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Gallien-Krueger MicroBass-III Series. Gallien-Krueger MicroBass-III Series 12 pagina's. Gallien-krueger mb150e/112: user guide
Pagina afdrukken
- 1. Owner's Manual
- 2. Warranty Card
- 3. Safety Instructions Sheet
- 4. Table of Contents
- 5. Power Cord
- 6. Safety Information
- 7. GK Philosophy
- 8. Setup & Quickstart
- 9. Front Panel Controls
- 10. Internal/External Speakers
- 11. Rear Panel Controls
- 12. Sample Settings
- 13. Sound Advice
- 14. Tech Talk
- 15. Specifications
Safety Information
Please read all enclosed safety precautions, before
connecting or operating this product.
Verify Line Voltage and Amperage Before Use:
Your new MicroBass Series amplifier has been
factory configured for use with:
120 Volt/60Hz 15 A circuit for USA/Canada.
230 Volt/50Hz 10 A circuit for UK/Australia.
240 Volt/50Hz 10 A circuit for Europe.
100 Volt/50Hz 15 A circuit for Japan.
220 Volt/50Hz 10 A circuit for Korea.
Connecting the amplifier to a line with specifications
other than indicated above can create a safety or
fire hazard and may damage the amplifier. If you
have any questions about the voltage requirements
for your specific model, or about the line voltage
in your area, contact your dealer before plugging
the unit into a wall outlet.
Verify AC Circuit Capacity Before Use:
The high power output of your amplifier may require
heavy current draw under full-load conditions. To
insure proper performance and avoid potential safety
hazards, we recommend connection to line circuits
with amperage specified "as above". Connecting
multiple amplifiers to the same circuit, or connect-
ing the amplifier to the same circuit used by other
heavy-power devices, such as high-wattage lights,
may cause circuit breakers to trip. It is always a
good idea to avoid using any audio equipment on
the same AC circuit as equipment with motors, such
as air conditioners or refrigerators. This will lessen
the possibility of power variation and electrical
start-up noise affecting your sound.
AC Power Cord:
To avoid safety hazards, use only the power cord
supplied with your unit. If a replacement cord is
needed, make certain that to use a standard IEC
compliant cord. Damaged power cords should be
replaced immediately.
MicroBass-III Series
Connecting to AC Power:
When setting up, make certain that the AC plug
is easily accessible. If mounting in a rack, ensure
that the AC mains can be easily disconnected by
a plug or by an all-pole disconnect switch on or
near the rack.
Disconnect When Not In Use:
If you do not intend to use the amplifier for a
considerable length of time, disconnect the plug
from the AC outlet. Just switching the unit off
does not mean that it is fully disconnected from
the AC Mains. To isolate the unit from the AC
mains, you must disconnect the power cord from
the unit and the AC outlet. When disconnecting
the power cord always pull from the plug, never
pull from the cord.
Do Not Open the Amplifier Enclosure:
There are no user-serviceable components inside
this product. Opening the amplifier enclosure
may present a shock hazard, and modification
to the product will void your warranty. If liquid
enters the unit, or any metal object such as a paper
clip, wire, or staple accidentally falls inside the
enclosure, disconnect the unit from the AC power
source immediately and consult an authorized
service station.
Unpacking:
The carton and packing materials used in shipping
your new amplifier were specifically designed to
cushion it from the shocks and vibration that occur
during transport. We suggest that you save the carton
and packing materials for use in shipping, in the
event you move, or the amplifier needs repair.
3