HIGOAL 2R Installatie- en veiligheidshandleiding - Pagina 2

Blader online of download pdf Installatie- en veiligheidshandleiding voor {categorie_naam} HIGOAL 2R. HIGOAL 2R 2 pagina's. Smart operation system

Pagina afdrukken
2
INSTALLATION AND SAFETY GUIDE
Installation will be performed by a certified expert.
Disconnect main power before installation.
Wires connection will be done according the diagram
in the back of the panel.
C = Common power input
R1 = 1st output, 5amp
R2 = 2nd output, 5amp
+12 = 12v power supply, 0.5 amp
-12 = common power supply and dry contact
K1 = Dry contact for R1
K2 = Dry contact for R2
To use 2 dry contact
Maintain a steady, straight installation against
outputs as 110/220V,
the wall.
bridge between C and L
Assembling panel's glass can be done in one
direction only.
Assembling the panel to the wall mount
In a plaster wall, install
(3/4 gang box) using the attached screws.
Shutter connection/Wiring A momentary button
a 3-gang wall mount
without butterfly screws.
requires changing the Dipswitch status.
A guide is attached to every smart panel.
3
Dipswitch
Under the panel glass there is a dipswitch which used to configure (using the attached pin)
R1
On-Off mode / Shutter mode / Shutter work time / Momentary mode / Safety mode. Configure
buttons before scanning.
FB
8
8
7
7
R2
6
6
Timer On
5
5
4
4
3
3
Safety On
12V
2
K1
K2
- +
2
Timer On
1
1
Shutter mode
ON
ON/OFF
2 dry contact
TIME 1
5/8
4 Work times
inputs for
1 min
4/7
for outputs
outputs
(Timer Mode,
Shutter)
TIME 2
5/8
4/7
Momentary
TIME 3
5/8
3 mins
4/7
TIME 4
5/8
7 mins
4/7
Dipswitches 7/8 – Output 2 work time
Timer Off
Dipswitch 6 – Output 2 timer On-Off
Dipswitches 4/5 – Output 1 work time
Safety Off
Dipswitch 3 – Output 1 Safety mode
Timer Off
Dipswitch 2 – Output 1 timer On-Off
On-Off mode
Dipswitch 1 – Outputs 1/2 Shutter mode
OFF
Dipswitch
1. Default work time for shutter mode is 1 min, in order to change
time, turn dipswitch 2 to On and set dipswitches 4/5
2. Dry contacts are parallel to buttons, for integrating 3rd party
systems, sensors and external switches
3. Built in 12v / 0.5amp power supply for external sensors
4. Setting timer mode to output is suitable with external sensor
connected by dry contact
5. Momentary mode – suitable with HIGOAL dimmer board
4
Operation Guide
After connecting and turn on the power, the button LEDs will turn on in blue, and the Central FB
button will turn on in White.
Disassembling the glass will be done using
a flat screwdriver in the left center of
the panel.
Assembling the glass after power on,
will be made when the panel is in locked mode.
20 seconds after assembling the glass you will be able unlock the panel, refer to page 6.
Button LEDs will decrease their intensity after 2 minutes, a short press on any button will increase
the intensity back.
Operation Buttons' LEDs color
FB button LEDs color
Blue – channel off.
Blue – Panel locked.
Green – channel On.
Red – Network disconnected
Light blue – Copy button.
Green – Network connected
Yellow – Scenario button.
White – Factory mode
Red – Momentary button.
Yellow – FW updated successfully
Download HIGOAL App from App store / Play store,
follow instructions and input all user details.
Scan each panel separately in order to connect it to
the Wi-Fi and App