DEA SYSTEM 203 2 Installatie- en gebruikershandleiding - Pagina 2

Blader online of download pdf Installatie- en gebruikershandleiding voor {categorie_naam} DEA SYSTEM 203 2. DEA SYSTEM 203 2 3 pagina's.

Pagina afdrukken

203_2

This booklet is an integral and essential part of the product and must be delivered to the

user. Carefully read the warnings contained inside that provide important information

regarding safety during installation, use and maintenance.

OVERVIEW

The DEA 203_2 control panel has been designed to control the "DEA SYSTEM" automa-

tion devices for both sliding gates and garage doors powered by 230V single-phase

motors, and comes complete with electronic motor

control for the detection of any obstacles present and an inertia limitation system for

use with sliding gates. The widest versatility, easy installation and complete respect for

the European regulations in force regarding electromagnetic compatibility and electric

safety are the unit's main characteristics; in particular, DEA SYSTEM ensures conformity

to the following European Directives: 89/336/EEC, 73/23/EEC and subsequent amend-

ments.

DEA SYSTEM reminds all users that the selection, configuration and installation of all the

devices and materials in the entire automation must be performed in respect of the

regulations in force in the nation of installation.

TECHNICAL DATA

Power supply

Flashing light output

Gate open signal light/courtesy light output

Auxiliary power supply output

Electric lock output

Max. motor power

Fuse F1

Fuse F2

Max pause time

Max work time

The work time you set must anyway allow to respect the maximum working time admit-

ted for the type of motor you are using. Please refer to the data on the motor label.

ELECTRICAL SYSTEM CONFIGURATION

(See fig. 1)

IMPORTANT: Any installation, maintenance, cleaning or repair operations on any part

of the automatism must be performed exclusively by qualified personnel, and all such

operations must be performed only after first disconnecting the power supply. Always

keep the 230V cables (power supply, motor, starting condenser, flashing light, courtesy

light) separate from the low voltage cables (controls, electric lock, antenna, and auxil-

iary power supply) and fasten these latter using adequate clamps near the terminal

boards. Install a multiple pole switch with a contact opening of 3 mm provided with

protection against overloads upstream from the automatism. Use a cable with a mini-

mum section of 3X1.5 mm² (such as H07RN-F type) for the power supply and scrupu-

lously respect all the regulations in force regarding electrical systems in the nation of

installation.

TERMINAL BOARD CONNECTION:

(See fig. 1)

1-2:

Power supply: 230V AC +/-10% 50 Hz (F = phase, N = neutral)

3-4

Courtesy light output 230 V AC 50 Hz max 40W (DIP8 = ON)

Gate open indicator light output: 230 V AC 50 Hz max 40W (DIP8 = OFF)

5-6

Flashing light output: 230 V AC 50 Hz max 40W

7-8-9

Motor output (7 = open, 8 = common, 9 = close)

10-11

electric lock output 12V AC 15VA

Common inputs

FCA opening limit-switch input (N.C.) stops the motor's opening stroke

FCC closing limit-switch input (N.C.) stops the motor's closing stroke

APRE PEDONALE opens the gate to a width of only 1.5 (N.O.)

FOTO Photocell Art. 104/105 input (N.C) inverts movement during closing, and

if enabled during opening stops movement

STOP stop button input (N.C) stops movement in any situation

APRE open/close button input (N.O.) can function in both step-by-step mode

and inversion mode

IMPORTANT: All N.C. inputs not used must be bridged towards the common inputs

terminal.

Antenna ground

Antenna signal

21-22

Auxiliary power supply output: 24V AC max 200mA

Radio receiver plug-in connector

OPERATION:

TIME SETTING

TCA

trimmer for the setting of the automatic closing time, after which the gate will

automatically close again.

TLAV

trimmer for the setting of the work time, after which the motor will stop during

both opening and closing.

Whenever the limit-switches are installed, the work time must be set to a value

that is a few seconds higher than the real time required for the stroke of the

motor.

force adjustment, amperometer

230V AC +/- 10% 50 Hz

:230V AC 50 Hz max 40W

:24V AC max 200 mA

:12V AC max 15V A

:500W

:160 mA 250V

250V

:80 s

:160 s (sliding version)

:80 s (garage door version)

DIP-SWITCHES FUNCTIONS

"collectivity"

function enabled: does not receive opening pulses

during opening and the gate open pause time

DIP1

OFF

"collectivity"

function disabled: receives opening pulses also during

opening and the gate open pause time

See description "reverser operation"

DIP2

OFF

See description "reverser operation"

"step-by-step" program: OPEN->opening, OPEN->stop, OPEN-

>closing...

DIP3

OFF

"inversion" program: OPEN->opening, OPEN->closing, OPEN-

>opening...

Sliding version: closing limit-switch delay disabled, anti-inertia de-

vice enabled

DIP4

OFF

Garage door version: closing limit-switch delay enabled, anti-inertia

device disabled

DIP5

Photocell operative also during opening: stops all movement until the

obstacle is removed

OFF

Photocell operative only during closing: inverts direction of movement

automatic closing disabled: after opening, it closes again only after

an opening pulse

DIP6

automatic closing enabled : after opening, and after the pause time

OFF

set, the gate automatically closes again

DIP7

Reverser disabled

OFF

Reverser enabled.

Terminals 3-4: courtesy light output 230V AC 50 Hz (delay: 50 sec-

onds)

DIP8

OFF

Terminals 3-4: gate open signal light output, 230V AC, 50 Hz

FORCE ADJUSTMENT

The 203_2 control panel is equipped with a device that permits the electronic adjust-

ment of motor force by adjusting the "forza" trimmer:

"FORZA":adjusts the intensity of the motor force during the stroke (rotate

clockwise to increase force, counter-clockwise to decrease force).

The motor force must be adjusted by keeping trimmer R32 "SENS" in

the MIN. position (entirely in clockwise direction) in order to avoid

the undesired intervention of the REVERSER. The sensitivity of the

reverser is made subsequently (see "Reverser operation").

REVERSER OPERATION

Whenever the "reverser" device is used, the limit-switches must also be installed

After setting the motor force, proceed to the setting of reverser sensitivity. Make sure

that the reverser is enabled (DIP7 OFF) and with the sensitivity set at minimum level

(trimmer R32 turned entirely clockwise) perform an opening movement. During closing,

stop the gate and slowly increase the reverser sensitivity (trimmer R32 turned counter-

clockwise) until the reverser intervenes

permits the identification of the sensitivity necessary for the intervention of the re-

verser as soon as the motor stops.

In any case, we recommend setting a sensitivity that is SLIGHTLY lower in order to

avoid the undesired intervention of the reverser by mechanical friction.

The position of DIP2 determines the reaction to the perception of the obstacle, and in

particular:

•

DIP 2 ON : during both opening and closing, the intervention of the reverser

inverts the direction of movement for 3 seconds and then stops it.

•

DIP 2 OFF : during opening, the intervention of the reverser stops movement,

and during closing inverts the direction of movement.

It is in any case obligatory to use appropriate safety devices in order to ensure the

impact force limitation values prescribed by the regulations in force in the nation of

installation.

IMPORTANT: limit-switches compulsory

(inversion of direction of movement). This