HIKOKI DH 18DBL Handling Instructies Handleiding - Pagina 7

Blader online of download pdf Handling Instructies Handleiding voor {categorie_naam} HIKOKI DH 18DBL. HIKOKI DH 18DBL 16 pagina's.

Pagina afdrukken
CAUTION
○ If the battery is charged while it is heated because
it has been left for a long time in a location subject to
direct sunlight or because the battery has just been
used, the charge indicator lamp of the charger lights for
0.3 seconds, does not light for 0.3 seconds (off for 0.3
seconds). In such a case, fi rst let the battery cool, then
start charging.
○ When the charge indicator lamp fl ickers (at 0.2-second
intervals), check for and take out any foreign objects in
the charger's battery connector. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service
Center.
○ Since the built-in micro computer takes about
3 seconds to confi rm that the battery being charged with
UC18YSL3 is taken out, wait for a minimum of 3 seconds
before reinserting it to continue charging. If the battery
is reinserted within 3 seconds, the battery may not be
properly charged.

MOUNTING AND OPERATION

Action
Removing and inserting the
battery
Charging
Remaining battery indicator
Installing / Removing the side
handle
Inserting SDS-plus drilling tools
Removing SDS-plus drilling tools
Selecting rotation direction
Selecting the operating mode
Adjusting the drilling depth
Changing the chisel position
Removing drill bit holder
(DH18DBQL, DH18DBML)*
Inserting drill chuck holder
(DH18DBQL, DH18DBML)
Inserting round shank applications
tools (DH18DBQL, DH18DBML)
Switch operation
How to use the LED light
Cleaning of the battery installation
compartment
Charging a USB device from a
electrical outlet
Charging a USB device and
battery from a electrical outlet
How to recharge USB device
When charging of USB device is
completed
Selecting accessories
*
If it is hard to pull out the drill chuck holder or the drill bit
holder, align the change lever with the
the lock grip.
For details on how to use the dust extraction unit, refer to
the separate instruction manual included with this tool.
(DH18DBML)
REACTIVE FORCE CONTROL
This product is equipped with a Reactive Force Control
(RFC) feature that reduces jerking of the tool body.
If the tool bit is suddenly overburdened, any jerking of the
tool body is reduced by activation of the slip clutch or by
stopping of the motor by the sensor built into the tool body.
If the motor is stopped because of overburdening detection
by the controller, this is indicated by blinking of the remaining
battery lamp while the switch is pulled. (Fig. 20)
Because the RFC feature may not activate or its performance
may be insuffi cient depending on the working environment
and conditions, be careful not to suddenly overburden the
tool bit while operating.
● Possible causes of sudden overburdening
1 Tool bit biting into material
2 Impact against nails, metal or other hard objects
3 Tasks involving prying or any excess application of
Also, other causes include any combination of the
aforementioned.
● When the reactive force control (RFC) is triggered
Figure
Page
1
10
2
10
3
10
4
10
5
11
6
11
7
11
8
11
9
11
10
11
11
12
LUBRICATION
12
12
Low viscosity grease is applied to this rotary hammer so
that it can be used for a long period without replacing the
13
12
grease. Please contact the nearest service center for grease
replacement when any grease is leaking form loosened
14
12
screw.
15
12
Further use of the rotary hammer despite the grease
shortage causes damage to reduce the service life.
16
12
CAUTION
17-a
13
17-b
13
18
13

MAINTENANCE AND INSPECTION

19
13
CAUTION
―
14, 15
1. Inspecting the tool
mark and turn
7
pressure, etc.
When the RFC is triggered and the motor stops, turn
off the tool's switch and remove the cause of the
overburdening before continuing operation.
Fig. 20
A specifi c grease is used with this machine, therefore,
the normal performance of the machine may be badly
aff ected by use of diff erent grease. Please be sure to let
one of our service centers to undertake replacement of
the grease.
Be sure to turned off the switch and remove the battery
before maintenance and inspection.
Since use of as dull tool will degrade effi ciency and
cause possible motor malfunction, sharpen or replace
the tool as soon as abrasion is noted.