ENGLISH
Cleaning and maintenance
CLEANING
WARNING!
- Never use steam cleaning equipment.
- Only clean the oven when it is cool to the touch.
- Disconnect the appliance from the power supply.
- Oven exterior
IMPORTANT: do not use corrosive or abrasive detergents. If any of
i
these products accidentally comes into contact with the appliance,
clean immediately with a damp cloth.
• Clean the surfaces with a damp cloth. If it is very dirty, add a few drops
of washing up detergent to the water. Finish off with a dry cloth.
Oven interior
IMPORTANT: do not use abrasive sponges or metallic scrapers or
i
scourers. Over time, these can ruin enamelled surfaces and the oven
door glass.
• After every use, allow the oven to cool then clean it preferably while it
is still warm in order to remove built-up dirt and stains caused by food
residues (e.g. food with a high sugar content).
• Use proper oven detergents and follow the manufacturer's instructions to the
letter.
• Clean the door glass with a suitable liquid detergent. The oven door
can be removed to facilitate cleaning (see MAINTENANCE). Inner glass
is smooth to facilitate cleaning.
Accessories
Soak the accessories in water with washing up detergent immediately
after use, handling them with oven gloves if still hot.
Food residues can be easily removed using a brush or sponge.
MAINTENANCE
WARNING!
- Use safety gloves.
- Ensure the oven is cold before carrying out the following operations.
- Disconnect the oven from the power supply.
To remove the shelf guides
firmly grip the external part of the guide, and pull it towards you to extract
the support and the two internal pins from the lodging.
To reposition the shelf guides
position them near the cavity and initially insert the two pins into their
lodgings. Next, position the external part near
its lodging, insert the support, and firmly press towards the wall of the
cavity to make sure the shelf guide is properly secured.
To remove the door
1. Open the door fully.
2. Lift the catches and push them forwards as far as they will go (Fig. 1).
Fig. 1
3. Close the door as far as it will go (A), lift it up (B) and turn it (C) until it
is released (D) (Fig. 2, 3, 4).
Fig. 2
To refit the door
1. Insert the hinges in their seats.
2. Open the door fully.
3. Lower the two catches.
4. Close the door
Cleaning the glass
1. After removing the door and resting it on a soft surface with the
handle downwards, simultaneously press the two retaining clips and
remove the upper edge of the door by pulling it towards you.
2. Lift and firmly hold the inner glass with both hands, remove it and
place it on a soft surface before cleaning it.
3. To reposition the internal glass properly, be sure that the "R" can be
seen in the left corner.
First insert the long side of the glass indicated by "R" into the support
seats, then lower it into position.
4. Refit the upper edge: A click will indicate correct positioning. Make
sure the seal is secure before refitting the door.
To replace the lamp
5. Disconnect the oven from the power supply.
6. Unscrew the lamp cover (Fig. 5), replace the lamp (see note for lamp
type) and screw the lamp cover back on.
7.
Reconnect the oven to the power supply.
NOTE:
Only use 25W/230 V type G9, T300°C halogen lamps.
The lamp used in the appliance is specifically designed for electrical
appliances and it is not suitable for household room illumination
(Commission Regulation (EC) No 244/2009).
Lamps are available from IKEA Authorized Service Centre.
Cable
Power cable replacement (type H05 RR-F 3 x 1,5 mm2) must be carried
out by a qualified electrician. Contact IKEA Authorized Service Centre.
5
Fig. 3
Fig. 4
Fig. 5
Pagina afdrukken