IKEA LAGAN Handmatig - Pagina 15

Blader online of download pdf Handmatig voor {categorie_naam} IKEA LAGAN. IKEA LAGAN 24 pagina's. Examples of the load of the basket
Ook voor IKEA LAGAN: Montagehandleiding (8 pagina's), Gebruikershandleiding (20 pagina's), Gebruikershandleiding (16 pagina's), Gebruikershandleiding (20 pagina's), Gebruiksaanwijzing (48 pagina's), Gebruikershandleiding (16 pagina's), Gebruikershandleiding (24 pagina's), Handmatig (28 pagina's), Gebruiksaanwijzing (24 pagina's), Gebruikershandleiding (24 pagina's), Handmatig (4 pagina's), Gebruikershandleiding (12 pagina's), Handmatig (24 pagina's), Montagehandleiding (20 pagina's), Installatiehandleiding (20 pagina's), Handmatig (28 pagina's), Handmatig (32 pagina's), Handmatig (44 pagina's), Handmatig (16 pagina's), Handmatig (16 pagina's), Handmatig (24 pagina's), Handmatig (28 pagina's), Handmatig (28 pagina's), Gebruikershandleiding (28 pagina's), Handmatig (40 pagina's), Handmatig (48 pagina's), Gebruiks- en onderhoudshandleiding (25 pagina's), Handmatig (44 pagina's), Handmatig (40 pagina's), Handmatig (28 pagina's), Handmatig (28 pagina's), Gebruikershandleiding (24 pagina's), Handmatig (48 pagina's), Gebruikershandleiding (16 pagina's), Handleiding voor installatie-instructies (18 pagina's), Handmatig (48 pagina's), Snelstarthandleiding (4 pagina's), Handleiding voor installatie-instructies (16 pagina's), Handmatig (28 pagina's), Handmatig (28 pagina's), Handmatig (44 pagina's), Handmatig (48 pagina's), Handmatig (16 pagina's), Handmatig (32 pagina's), Handmatig (24 pagina's), Handmatig (25 pagina's), Handmatig (18 pagina's), Gebruikershandleiding (28 pagina's), Handmatig (44 pagina's), Handmatig (24 pagina's), Handmatig (32 pagina's), Handmatig (18 pagina's), Handmatig (48 pagina's), Handmatig (29 pagina's), Handmatig (29 pagina's), Handmatig (34 pagina's)

Pagina afdrukken

ENGLISH

ignite immediately and will seem to

blow's lightly when they do ignite, this is

usually due to air in the gas pipe which

should clear itself within seconds of

operation.

10. If after following the instructions given,

satisfactory performance cannot be

obtained, contact the local gas authority

for advice and assistance.

Before leaving - Check all connections for

gas leaks with soap and water. Ignite all

burners to ensure correct operation of gas

valves, burners and ignition. Turn gas taps

to low flame position and observe stability

of the flame. In case the appliance fails to

operate correctly after all checks have been

carried out, refer to the authorised service

provider in your area.

Adjustment to different type of gas

If the supply cord is damaged, it must be

replaced by the manufacturer, its service

agent or similarly qualified persons in order

to avoid a hazard.

WARNING

This operation must be performed by a

qualified technician.

If the appliance is intended to operate with

a different gas from the gas type stated on

the rating plate and information label on the

top of the hob, change the injectors.

Remove the information label and keep it

with the instructions booklet.

Use pressure regulators suitable for the gas

pressure indicated in the Instruction.

The gas nozzles must be changed

by After Sales Service or a qualified

technician.

Nozzles not supplied with the appliance

must be ordered from After Sales

Service.

Adjust the minimum setting of the taps.

NOTE: when liquid petroleum gas is used,

the minimum gas setting screw must be

tightened as far as it will go.

IMPORTANT: should you experience

difficulty in turning the burners knobs,

please contact the After Sales Service for the

replacement of the burner tap if found to be

faulty.

Replacing the injectors (see paragraph

"injector table")

Remove grids (A).

Extract burners (B).

Using a socket spanner of the

appropriate size unscrew the injector (C),

unscrew the injector to be replaced.

Replace it with the injector suitable for

the new type of gas.

Re-assemble the injector in (D).

Before installing the hob, remember to affix

the gas calibration plate supplied with

the injectors in such a way that it covers

the existing information relating to gas

calibration.