IKEA 30" (76.2 CM) WALL-MOUNT CANOPYRANGE HOOD Installatie-instructies en gebruiks- en onderhoudshandleiding - Pagina 5

Blader online of download pdf Installatie-instructies en gebruiks- en onderhoudshandleiding voor {categorie_naam} IKEA 30" (76.2 CM) WALL-MOUNT CANOPYRANGE HOOD. IKEA 30" (76.2 CM) WALL-MOUNT CANOPYRANGE HOOD 44 pagina's. 30" (76.2 cm) wall-mount canopy range hood

Pagina afdrukken

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

Level

Drill with 1¼" (3.2 cm),

drill bits

Pencil

Wire stripper or utility knife

Tape measure or ruler

Pliers

Caulking gun and weatherproof caulking compound

Vent clamps

Jigsaw or keyhole saw

Flat-blade screwdriver

Metal snips

Phillips screwdriver

Parts needed

Home power supply cable

½" (12.7 mm) UL listed or CSA approved strain relief

3 UL listed wire connectors

For vented installations, you will also need:

1 wall or roof cap

Metal vent system

For non-vented (recirculating) installations, you will also

need:

Charcoal Filter Kit Part Number W10412939 for non-vented

(recirculating) installations only. See "Assistance or Service"

section to order.

6" (15.2 cm) dia. round metal vent duct - length required is

determined by ceiling height.

Parts supplied

Remove parts from packages. Check that all parts are included.

Hood canopy assembly with blower, light bulb and canopy

glass already installed

Vent transition

Metal grease filter

Vent cover support bracket

Mounting template

2-piece vent cover

Air deflector (for non-vented [recirculating] installations only)

8 - 4.2 x 8 mm screws (T20

6 - 5 x 45 mm mounting screws (#2 Phillips drive)

2 - 8 x 40 mm wall anchors (masonry)

4 - 10 x 50 mm wall anchors (drywall)

T10 Torx

®†

adapter

T20

Torx

adapter

2 - 3.5 x 9.5 mm screws (T10 drive)

†®TORX and T20 are registered trademarks of Saturn Fasteners, Inc.

INSTALLATION REQUIREMENTS

" (3.2 mm), and

" (7.9 mm)

®†

drive)

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

Have a qualified technician install the range hood. It is the

installer's responsibility to comply with installation clearances

specified on the model/serial rating plate. The model/serial rating

plate is located behind the left filter on the rear wall of the vent

hood.

Canopy hood location should be away from strong draft areas,

such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given

dimensions provide minimum clearance.

Grounded electrical outlet is required. See "Electrical

Requirements" section.

The canopy hood is factory set for venting through the roof or

wall. For non-vented (recirculating) Installation see "For non-

vented (recirculating) installation only" in the "Connect Vent

System" section. Charcoal Filter Kit Part Number W10412939 is

available from your dealer or an authorized parts distributor.

All openings in ceiling and wall where canopy hood will be

installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home

Construction and Safety, Title 24, HUD, Part 280) or when such

standard is not applicable, the standard for Manufactured Home

Installation 1982 (Manufactured Home Sites, Communities and

Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local

codes.

Product Dimensions

10 "

(27.6 cm)

20"

(50.8 cm)

(33.5 cm)

30" (76.2 cm)