IKEA DATID Installatie-instructies en gebruiks- en onderhoudshandleiding - Pagina 5

Blader online of download pdf Installatie-instructies en gebruiks- en onderhoudshandleiding voor {categorie_naam} IKEA DATID. IKEA DATID 18 pagina's. 30" (76.2 cm) wall-mount canopy range hood
Ook voor IKEA DATID: Gebruikershandleiding (16 pagina's), Installatiehandleiding (12 pagina's), Handmatig (24 pagina's)

Pagina afdrukken
IKEA DATID Installatie-instructies en gebruiks- en onderhoudshandleiding

Tools and Parts

Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools
listed here.
Tools needed
■ L evel
■ D rill with 1¼" (3.0 cm), ³⁄
8
■ P encil
■ W ire stripper or utility knife
■ T ape measure or ruler
■ P liers
■ C aulking gun and weatherproof caulking compound
■ V ent clamps
■ J igsaw or keyhole saw
■ F lat-blade screwdriver
■ M etal snips
■ P hillips screwdriver
■ M etric hex key set
Parts needed
■ H ome power supply cable
■ ½ " (12.7 mm) UL listed or CSA approved strain relief
■ 3 UL listed wire connectors
For vented installations, you will also need:
■ 1 wall or roof cap
■ M etal vent system
For non-vented (recirculating) installations, you will also need:
■ C harcoal Filter Kit Part Number W10412939 for non-vented
(recirculating) installations only. See "Assistance or Service"
section to order.
■ 6 " (15.2 cm) dia. round metal vent duct - length required is
determined by ceiling height.
Parts supplied
Remove parts from packages. Check that all parts are included.
■ H ood canopy assembly with ventilator and light bulbs installed
■ V ent transition with back draft dampers installed
■ M etal grease filter(s)
■ V ent cover support bracket
■ M ounting template
■ A ir deflector with extensions (for non-vented installations)
■ 2 -piece vent cover
■ 6 - 3.5 x 6.5 mm screws
■ 2 - 2.9 x 6.5 mm screws
■ 6 - 5 x 45 mm mounting screws
■ 6 - 8 x 40 mm wall anchors
■ T 10 Torx
adapter
®†
■ T 20
Torx
adapter
®
®†
†
®
TORX and T20 are registered trademarks of Acument Intellectual Properties, LLC.
INSTALLATION REQUIREMENTS
" (9.5 mm), and ³⁄
" (4.8 mm) drill bits
16
■ 2 - Flat washers
■ 4 - 4.2 x 8 mm screws
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
Have a qualified technician install the range hood. It is the
installer's responsibility to comply with installation clearances
specified on the model/serial rating plate. The model/serial
rating plate is located behind the filter on the rear wall of the
vent hood.
Canopy hood location should be away from strong draft areas,
such as windows, doors and strong heating vents.
Cabinet opening dimensions that are shown must be used.
Given dimensions provide minimum clearance.
Grounded electrical outlet is required. See "Electrical
Requirements" section.
The canopy hood is factory set for venting through the roof
or wall. For non-vented (recirculating) Installation see "For
Non-vented (recirculating) Installation Only" in "Connect Vent
System" section. Charcoal Filter Kit Part Number W10412939 is
available from your dealer or an authorized parts distributor.
All openings in ceiling and wall where canopy hood will be
installed must be sealed.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured Home Construction Safety Standards, Title
24 CFR, Part 328 (formerly the Federal Standard for Mobile
Home Construction and Safety, Title 24, HUD, Part 280)
or when such standard is not applicable, the standard for
Manufactured Home Installation 1982 (Manufactured Home
Sites, Communities and Setups) ANSI A225.1/NFPA 501A, or
latest edition, or with local codes.
Product Dimensions
10⁷⁄₈"
9³⁄₈"
(27.6 cm)
(23.8 cm)
30" (76.2 cm)
*For non-vented (recirculating) installations
**For vented installations
14"
(35.5 cm)
*32³⁄₈" (82.2 cm) min.
**31³⁄₈" (79.7 cm) min.
*44³⁄₄" (113.7 cm) max.
**41" (104.1 cm) max.
13³⁄₄"
(34.9 cm)
2" (5.1 cm)
18⁷⁄₈" (48.0 cm)
5