IKEA LAGAN Handmatig - Pagina 15

Blader online of download pdf Handmatig voor {categorie_naam} IKEA LAGAN. IKEA LAGAN 24 pagina's. Examples of the load of the basket
Ook voor IKEA LAGAN: Montagehandleiding (8 pagina's), Gebruikershandleiding (20 pagina's), Gebruikershandleiding (16 pagina's), Gebruikershandleiding (20 pagina's), Gebruiksaanwijzing (48 pagina's), Gebruikershandleiding (16 pagina's), Gebruikershandleiding (24 pagina's), Handmatig (28 pagina's), Gebruiksaanwijzing (24 pagina's), Gebruikershandleiding (24 pagina's), Handmatig (4 pagina's), Gebruikershandleiding (12 pagina's), Handmatig (24 pagina's), Montagehandleiding (20 pagina's), Installatiehandleiding (20 pagina's), Handmatig (28 pagina's), Handmatig (32 pagina's), Handmatig (44 pagina's), Handmatig (16 pagina's), Handmatig (16 pagina's), Handmatig (24 pagina's), Handmatig (28 pagina's), Handmatig (28 pagina's), Gebruikershandleiding (28 pagina's), Handmatig (40 pagina's), Handmatig (48 pagina's), Gebruiks- en onderhoudshandleiding (25 pagina's), Handmatig (44 pagina's), Handmatig (40 pagina's), Handmatig (28 pagina's), Handmatig (28 pagina's), Gebruikershandleiding (24 pagina's), Handmatig (48 pagina's), Gebruikershandleiding (16 pagina's), Handleiding voor installatie-instructies (18 pagina's), Handmatig (48 pagina's), Snelstarthandleiding (4 pagina's), Handleiding voor installatie-instructies (16 pagina's), Handmatig (28 pagina's), Handmatig (28 pagina's), Handmatig (44 pagina's), Handmatig (48 pagina's), Handmatig (16 pagina's), Handmatig (32 pagina's), Handmatig (24 pagina's), Handmatig (25 pagina's), Handmatig (18 pagina's), Gebruikershandleiding (28 pagina's), Handmatig (44 pagina's), Handmatig (24 pagina's), Handmatig (32 pagina's), Handmatig (18 pagina's), Handmatig (48 pagina's), Handmatig (29 pagina's), Handmatig (29 pagina's), Handmatig (34 pagina's), Handleiding voor installatie-instructies (42 pagina's)

IKEA LAGAN Handmatig
ENGLISH
ignite immediately and will seem to
blow's lightly when they do ignite, this is
usually due to air in the gas pipe which
should clear itself within seconds of
operation.
10. If after following the instructions given,
satisfactory performance cannot be
obtained, contact the local gas authority
for advice and assistance.
Before leaving - Check all connections for
gas leaks with soap and water. Ignite all
burners to ensure correct operation of gas
valves, burners and ignition. Turn gas taps
to low flame position and observe stability
of the flame. In case the appliance fails to
operate correctly after all checks have been
carried out, refer to the authorised service
provider in your area.
Adjustment to different type of gas
If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualified persons in order
to avoid a hazard.
WARNING
-
This operation must be performed by a
qualified technician.
If the appliance is intended to operate with
a different gas from the gas type stated on
the rating plate and information label on the
top of the hob, change the injectors.
Remove the information label and keep it
with the instructions booklet.
Use pressure regulators suitable for the gas
pressure indicated in the Instruction.
-
The gas nozzles must be changed
by After Sales Service or a qualified
technician.
-
Nozzles not supplied with the appliance
must be ordered from After Sales
Service.
-
Adjust the minimum setting of the taps.
NOTE: when liquid petroleum gas is used,
the minimum gas setting screw must be
tightened as far as it will go.
IMPORTANT: should you experience
difficulty in turning the burners knobs,
please contact the After Sales Service for the
replacement of the burner tap if found to be
faulty.
Replacing the injectors (see paragraph
"injector table")
-
Remove grids (A).
-
Extract burners (B).
-
Using a socket spanner of the
appropriate size unscrew the injector (C),
unscrew the injector to be replaced.
-
Replace it with the injector suitable for
the new type of gas.
-
Re-assemble the injector in (D).
Before installing the hob, remember to affix
the gas calibration plate supplied with
the injectors in such a way that it covers
the existing information relating to gas
calibration.
D
C
15
A
B
B