KitchenAid YKGCT305E Handleiding voor installatie-instructies - Pagina 4

Blader online of download pdf Handleiding voor installatie-instructies voor {categorie_naam} KitchenAid YKGCT305E. KitchenAid YKGCT305E 10 pagina's. 30" ana 36" gas sealed burner glass cooktops

Pagina afdrukken

__... grate

burner cap

knob

burner

burnerbox

Install the pressure regulator with the

arrow on the regulator pointing up

toward unit and in a position where

you can reach the access cap.

Lift entire cooktop up from cutout when

repositioning

cooktop in countertop opening

to prevent scratching

countertop,

Insert cooktop into countertop opening.

Center the cooktop in the cutout. Check

that front edge of cooktop is parallel to

front edge of countertop. Check that all

required clearances are met. Use a pencil to

outline the rear of the cooktop on the countertop.

Remove the cooktop from the cutout and place

upside down on a protected surface.

so each is

Attach the mounting brackets to each

side of the burner box with the 5/16"

(0.80cm) screws. Do Not tighten the

screws. Turn the mounting brackets

under the burner box.

einsert the cooktop into countertop

opening. Check that cooktop is

parallel to front edge of countertop.

Lift entire cooktop to make

adjustments so the foam sealing strip can seal

properly.

Fire Hazard

Do Not make connection too tight. The

regulator is die cast,

Overtightening

may crack regulator

resulting in a gas leak and possible fire or

explosion,

3/8" (0.95cm) nipple flexible connector 3/8" (0.95cm) nipple

3/8" (0.95cm) adapters

manual shutoff valve

pressure

regulator

All connections must be wrench-tightened.

Assemble the flexible connector

from the gas supply pipe to the

•

pressure regulator in order:

manual shutoff valve, 3/8"

(0.95cm) nipple, 3/8" (0.95cm) adapter, flexible

connector, 3/8" (0.95cm adapter, and 3/8"

(0.95cm) nipple.

I Use pipe'j°int

c°mp°und

made

f°r

use with NATURAL and L.P. gas

•

to seal all gas connections. If

flexible connectors are used, be

certain connectors are not kinked.

Injury Hazard

Do Not overtighten

screws.

Overtightening

screws could cause

personal injury.

glass cooktop

countertop

c,a% n'g4Cm)

_,,,

screw

=..:,

mounting

5/16" (0.80cm)

bracket

clamp bracket screw

Rotate mounting brackets away from

burner box. Tighten the mounting

brackets to the burner box. Insert the

2-1/2" (6.4cm) clamping screws into

the mounting brackets. Use a screwdriver to

tighten screws against the underside of

countertop.

shutoff valve

to cookto_

to gas

supply line

Open

the shutoff valve

in the gas

supply

line. Wait a few minutes

for

•

gas to move through

the gas line.

Fire Hazard

Do Not use an open flame to test for leaks

from gas connections.

Checking for leaks with a flame may result

in a fire or explosion.

Panel C

I12 I

Use a brush and liquid detergent

to test all gas connections for

•

leaks. Bubbles around

connections will indicate a leak. If

a leak appears, shut off gas valve controls and

adjust connections.

Then check connections

again. NEVER TEST FOR GAS LEAKS WITH

A MATCH OR OTHER FLAME. Clean all

detergent solution from cooktop.

j131

Plug the power

(r__K___

supply cord into

•

the grounded

outlet.

Place

14•

burner

grates over

burners and

caps. Install control knobs

on valve stems.

Electronic

Ignition

System-

initial lighting

Cooktop burners use electronic igniters in place

of standing pilots. When the cooktop control

knob is pushed in and turned to the "LITE"

position, the system creates a spark to light the

burner. This sparking continues until the control

knob is turned to the desired setting.

I1 5 ] O'ec"'"e

operation

•

of the

cooktop

burners. Push in and

_,_ IN

turn each control knob

to "LITE" position. The flame should light within 4

seconds. Do Not leave the knob in the "LITE"

position

after burner lights.

If burners do not light properly, turn control knob

to the "OFF" position. Check that burner cap is in

the proper position. Check that power supply

cord is plugged in and that circuit breaker or

house fuse has not blown. Check that the shutoff

valve is in the "ON" position. Check operation

again. If a burner does not light at this point,

contact your KitchenAid dealer for assistance.

Check each cooktop

burner for proper flame.

•

The small inner cone

should have a very

distinct blue flame approximately

1/2"

(1.3cm) long. The outer cone is not as

distinct as the inner cone.

I17 I

Push in and turn each control knob

to the "LO" (or simmer) setting. The

•

"LO" setting of each burner has

been factory set to the lowest

setting available to provide reliable reignition of the

burner. If it does not stay lit on the "LO" setting,

check "LO" setting as follows:

a. Turn control to "LITE" until burner ignites.

b. Quickly turn knob down to LOWEST POSITION.

c. If burner goes out, readjust valve as follows:

Remove the surface burner control knob. Insert a

flat-blade screwdriver into the hollow valve stem

and engage the slotted screw inside. Flame size

can be increased or decreased with the turn of the

screw. Adjust flame until you can quickly turn knob

from "LITE" to LOWEST POSITION without

extinguishing the flame. Flame should be as small

as possible without going out.

To get the most efficient

use

from your new cooktop,

read

your KitchenAid

Use and Care

Guide.

Keep Installation

Instructions

and Guide close

to cooktop

for easy reference.

L.P, gas conversion

No attempt shall be made to convert the

appliance from the gas specified on the

model/serial rating plate for use with a different

gas without consulting the servicing gas supplier.

Conversion

must be done by a service

technician. Conversion Kit No. 4173627 is

available from your KitchenAid dealer or

authorized parts distributor.