KitchenAid Architect II KUDS30IVSS Gebruiksaanwijzing - Pagina 5
Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} KitchenAid Architect II KUDS30IVSS. KitchenAid Architect II KUDS30IVSS 20 pagina's. Capacity: standard
Ook voor KitchenAid Architect II KUDS30IVSS: Energie Handleiding (2 pagina's)
![KitchenAid Architect II KUDS30IVSS Gebruiksaanwijzing](/uploads/products/server2/2077878/2077878.jpg)
OPTION SELECTIONS
OPTIONS
DISH LOAD TYPES
Pans, casseroles, etc. with
tough food soil.
To sanitize your dishes and
glassware in accordance
with NSF/ANSI Standard
184 for Residential
Dishwashers.
Loads containing tough,
baked-on food.
For best drying results, dry
dishes with heat.
To run your dishwasher at
a later time or during off-
peak hours.
Control Lock
To avoid unintended use of
your dishwasher, or cycle
and option changes during
a cycle.
IMPORTANT: The sensor in your dishwasher monitors the soil level. Cycle time and/or water usage can vary as the sensor adjusts the
cycle for the best wash performance. If the incoming water is less than the recommended temperature or food soils are heavy, the cycle
will automatically compensate by adding time, heat and water as needed.
CONTROLS AND
CYCLE STATUS
CONTROL
PURPOSE
To start or resume a
wash cycle
To cancel wash
cycle
To follow the
progress of your
dishwasher cycle
DESCRIPTIONS
Activates the PROSCRUB
intensified water spray to the back of the lower level rack.
May add heat and time to the cycle.
Raises the water temperature in the final rinse to
approximately 155°F (68°C). This high temperature rinse
sanitizes your dishes and glassware in accordance with
NSF/ANSI Standard 184 for Residential Dishwashers.
Certified residential dishwashers are not intended for
licensed food establishments.
The Sanitize or Sani Rinse option adds heat and time to the
cycle.
Increases the target water temperature during the wash
portions of the cycle.
Adds heat, wash time and water to the cycle.
Turn OFF when loads contain plastic dinnerware that may be
sensitive to high temperatures.
This option with the use of rinse aid will provide the best
drying performance.
Delays the start of a cycle up to 4 hours.
Select a wash cycle and options. Press 4 Hour Delay. Press
START/RESUME. Close the door firmly.
To turn on Lock, press and hold Heat Dry for at least
4 seconds.
To turn off Lock, press and hold Heat Dry for at least
4 seconds.
When Control Lock is lit, all buttons are disabled. If you press
any pad while your dishwasher is locked, the light flashes
3 times. The dishwasher door can be opened while the
controls are locked.
COMMENTS
If the door is opened during a cycle or the power is interrupted, the START/RESUME indicator
flashes. The cycle will not resume until the door is closed and START/RESUME is pressed.
Note: If the START/RESUME button is located on top of door, push door firmly closed within
3 seconds of pressing START/RESUME.
Close the door firmly. The dishwasher starts a 2-minute drain (if needed). Let the dishwasher
drain completely.
Clean indicator glows when a cycle is finished.
If you select the Sani Rinse option, when the Sani Rinse cycle is finished, the Sanitized indicator
glows. If your dishwasher did not properly sanitize your dishes, the light flashes at the end of the
cycle. This can happen if the cycle is interrupted, or the water could not be heated to the required
temperature. The light goes off when you open and close the door or press CANCEL.
®
spray jets and provides
USE WITH:
Heavy Duty or Normal
cycle
Normal cycle. Heavy
Duty cycle automatically
uses Sani Rinse. Only
these sanitization cycles
have been designed to
meet the NSF/ANSI
requirements.
Heavy Duty or Normal
cycles
All cycles, except Rinse
Only. Automatic with all
wash cycles unless you
turn it off.
All cycles, except Rinse
Only
Anytime
5