KitchenAid Briva Handleiding voor installatie-instructies - Pagina 6

Blader online of download pdf Handleiding voor installatie-instructies voor {categorie_naam} KitchenAid Briva. KitchenAid Briva 6 pagina's. In-sink dishwasher

Pagina afdrukken

WARNING

Electrical Shock Hazard

Electrically ground dishwasher.

Connect ground wire to green

ground connector in terminal

box.

Do not use an extension cord.

Failure to do so can result in

death, fire, or electrical shock.

ground

wire

direct

green ground

wire

7F .

Pull direct wire through

conduit connector and connect wires

as follows:

• Form ground wire into a hook and

wrap clockwise around ground

screw under washer. Tighten

ground screw securely.

• Use twist-on connectors of proper

size to connect direct wire to

16-gauge wire dishwasher wiring.

Connect black wires together and

white wires together.

• Tighten conduit connector screws.

terminal

box

tabs

7G.

Reinstall terminal box.

Important: The tabs MUST be under

the terminal box as shown.

Part No. 8529408

® Registered Trademark/™ Trademark of KitchenAid, U.S.A.

® Teflon is a registered trademark of E.I. Du Pont de Nemours and Company.

apply Teflon

or pipe joint

compound

DO NOT apply Teflon

tape or pipe joint

compound

Apply Teflon

compound to 90° elbow fitting and

connect fitting to water inlet valve.

Use adjustable wrench and tighten

elbow until snug and facing the

direction needed for your water fill

line installation.

IMPORTANT: If you are installing the

Hot Water Accessory Tank, go back

to its Installation Instructions and

complete the installation at this time.

Connect the dishwasher water

screw

fill line.

• Slide nut onto copper tubing about

1 inch.

• Slide ferrule onto the tubing. Do

not position ferrule on end of

tubing.

• Put tubing into fill fitting as far as it

will go.

• Slide nut and ferrule forward and

start nut onto elbow threads. Be

careful when handling and

positioning copper tubing. It bends

and kinks easily.

• With copper tubing pushed into

elbow as far as it will go, use a 5/8"

open-end wrench and tighten the

compression nut securely.

10.

Connect hot and cold water

lines to faucet.

11.

Connect the sink and

dishwasher drain plumbing.

12.

Turn water supply on to

both dishwasher and sink faucet.

Check for leaks.

tape

water inlet

valve

water fill line

connection

tape or pipe joint

13.

Check that there is power to

the outlet and plug power supply

cord into 3-prong grounded outlet. If

direct wired, turn on power supply.

Important: The following steps

MUST be done BEFORE using the

dishwasher, to test and activate the

GFCI.

test

reset

indicator

14.

Press the reset button on

the GFCI. The indicator should be

visible.

15.

Press the test button on the

GFCI. The indicator should

disappear.

16.

Press the reset button. The

indicator should reappear.

If the GFCI fails this test, DO NOT use

dishwasher. Call the KitchenAid

Customer Interaction Center toll-free

at 1-800-422-1230 for assistance.

17.

Refer to Use and Care Guide

that came with this dishwasher and

run dishwasher through a complete

cycle.

If Hot Water Accessory Tank is

installed, wait about 45 minutes

before starting the next dishwasher

cycle to allow the hot water tank to

finish heating. (Refer to the

Installation Instructions and Use and

Care Guide supplied with Hot Water

Accessory Tank.)

When the hot water tank is first

heated, it is normal for a small

amount of water to be discharged

into the dishwasher.

Check for leaks.

Printed in U.S.A.

8/2002