Avantco 177CAG48MG Gebruikershandleiding - Pagina 7
Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Avantco 177CAG48MG. Avantco 177CAG48MG 15 pagina's. Commercial countertop griddles, charbroilers & ranges
Pagina afdrukken
User Manual
First-Time Use
Against shock damage or rocking from transportation, the sides and waste tray have a protective
PVC film. Remove any plastics, straps, or protective film from the product before operating the
equipment.
COUNTERTOP GAS GRIDDLE, THERMOSTATIC & MANUAL
To protect the equipment against possible moisture damage between fabrication and installation on
site, the flat-tops are coated with a layer of vegetable shortening and brown paper.
In addition, you should remove grease and brown paper, cleaning should be performed with the aid
of a sponge, mild soap and water in small amount.
After this procedure, turn the burners on and leave them on for about 15 minutes, this will cause all
flat-top grill residue to be burned and eliminated. Only then will the equipment be ready for use.
COUNTERTOP GAS RADIANT CHAR BROILER
To protect the equipment against possible moisture damage between manufacture and installation
on site, the grills and baffle rails are coated with a layer of vegetable oil.
In addition, you should perform a cleaning with the help of a sponge, neutral soap and water in small
amounts. After this procedure, turn the burners on and leave them on for about 15 minutes, this will
cause all gas charbroiler residue to be burned and eliminated.
Only then will the equipment be ready for use.
COUNTERTOP GAS RANGE
You should perform a cleaning with the help of a sponge, neutral soap and water in small amounts.
Only then will the equipment be ready for use.
Product Ignition
If you need to adjust the pilot valves (one pilot valve corresponds to two burners) do the following:
Turn the pilot adjusting screw counterclockwise, then light the pilot with the aid of the igniter
1 .
(wick) accompanying the product and adjust the flame to a height of approximately 0.5 cm;
2 .
Turn on the gas valve by turning the knob counterclockwise to light the main burners;
To shut down completely, close the gas valves by turning the knob clockwise and turn the pilot
3 .
adjusting screw clockwise to close the gas for the pilots.
12
COUNTERTOP GAS GRIDDLE, THERMOSTATIC
1. Open the manual gas supply valve (which will release gas
into the product);
2. Immerse in alcohol the lighter (wick) that accompanies
the product and light it; Note: Make sure that the container
where the alcohol is located is away from the product and
wick after immersing.
3. Press lightly and rotate the handle to the pilot position.
4. Keep it pressed and take the igniter (wick) passing
between the pilot flame ignition hole in the product panel
until it comes into contact with the pilot and ignites the
flame;
5. Keep the knob pressed for 10 seconds after the pilot
flame is lit and turn the knob counterclockwise until
the wished temperature (use the knob to adjust the
temperature);
6. Make sure the burner is lit. If the burner does not light,
repeat the procedure;
COUNTERTOP GAS GRIDDLE, MANUAL
1. Open the manual gas supply valve (which will release gas
into the product).
2. Immerse in alcohol the lighter (wick) that accompanies
the product and light it; Note: Make sure that the container
where the alcohol is located is away from the product and
wick after immersing;
3. Take the igniter (bypass) past the ignition hole in the
flame of the pilot on the product panel until contact with the
pilot burner and until the flame ignites, repeat this procedure
on all pilots (see following image); Note: The ignition order
does not interfere with the use of the equipment;
4. Turn the knob corresponding to the burner you wish to
operate counterclockwise (adjust the flame through the
knob);
5. Make sure the burner is lit. If the burner does not light,
repeat the procedure;
6. After lighting all burners, you can turn off the burners
and turn them back on simply by turning the corresponding
knobs; Note: The pilot burner flame is factory set
according to the gas for which the product was originally
manufactured. Always check through the hole identified on
the panel as PILOT, if the pilot burner flame is lit. If it is not,
perform the procedures described above again.
www.AvantcoEquipment.com
www.AvantcoEquipment.com
User Manual
13