IKEA IUD4000WQ1 Gebruiks- en onderhoudshandleiding - Pagina 11

Blader online of download pdf Gebruiks- en onderhoudshandleiding voor {categorie_naam} IKEA IUD4000WQ1. IKEA IUD4000WQ1 36 pagina's.

Pagina afdrukken

You can change a cycle anytime during a cycle.

1. Lift the door latch to stop the cycle.

2. Turn the cycle control knob clockwise.

3. Check the detergent dispensers. They must be filled properly

for the new cycle.

NOTE: Turning the cycle control knob can cause the covered

detergent dispenser section to open and release the

detergent. Check the covered section if the cycle uses

detergent in both sections.

4. Close the door firmly until it latches. The dishwasher starts a

new cycle.

You can add an item anytime before the main wash starts, or the

cycle control knob reaches Normal Wash.

1. Lift up the door latch to stop the cycle. Wait for the spraying

action to stop before opening the door.

2. Open the door and add the item.

3. Close the door, but do not latch it. Wait 30 seconds for the air

in the dishwasher to warm up. This reduces the amount of

moisture escaping from the vent when restarting a cycle.

4. Close the door firmly until it latches. The dishwasher resumes

the cycle.

You can change an option anytime before the selected option

begins. For example, you can press an unheated drying option

anytime before drying begins.

No Heat Dry

Select this energy-saving

option to dry without heat. No heat

drying is useful when loads contain plastic dinnerware that may

be sensitive to high temperatures.

The dishes take longer to dry, and some spotting can occur. For

best drying, use a liquid rinse aid. Some items (such as plastics)

may need towel drying.

NOTE: The dishwasher

automatically heats the air in the

dishwasher during the "dry" portion of the cycle unless you

select No Heat Dry.

Heated

Dry

Select this option to dry dishes with heated air. For best drying

results, use a liquid rinse aid and heated drying.

NOTE: Heated Dry is an option with all cycles except Rinse Only.

Hi-Temp

Boost (on some models)

Select this option to add extra heat to the water in the Heavy

wash or Normal wash cycles. This helps remove food soil.

Reset Options

Select this option to change an option setting. You can change

option settings anytime during a cycle as long as the cycle has

not passed the point where the option is used. For example, you

can press No Heat Dry anytime before the cycle control knob

reaches Dry.

1. Press RESET OPTIONS.

2. Press 1 or more options.

Delay Hours (on some models)

Use Delay Hours to run your dishwasher at a later time or during

off-peak hours. You can add items to the load anytime during the

delay countdown. After adding items, close the door firmly until it

latches. The delay countdown

will not continue if the door is not

latched.

To delay the start

1. Close the door.

2. Select a wash cycle and option(s).

3. Turn the cycle control knob clockwise to the number of hours

you want the dishwasher to delay the start.

NOTES:

•

To cancel the delay, turn the cycle control knob to the desired

cycle.

•

Rinse Only and Normal wash cycles cannot be delayed.

Plate Warmer (on some models)

Use the Plate Warmer cycle to warm serving dishes or dinner

plates.

NOTE: Use the heated drying option with the Plate Warmer.

1. Close and latch the door.

2. Press HEATED DRY or RESET OPTIONS (depending on your

model).

3. Turn the cycle control knob to PLATE WARMER.

4. The cycle control knob will turn itself to OFF when the dishes

are ready.

During drying, you can see steam escaping through the vent at

the upper left corner of the door. This is normal as the heat dries

your dishes.

I_, i

| --

I I

_,,,

•

IMPORTANT." The vapor is hot. Do not touch the vent

during drying.

The overfill protection float (in the front right corner of the

dishwasher tub) keeps the dishwasher from overfilling. It must be

in place for the dishwasher to operate.

Check under the float for objects that may keep the protector

from moving up or down.