Makita 4305 Gebruikershandleiding - Pagina 7
Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Makita 4305. Makita 4305 8 pagina's. Variable speed
Ook voor Makita 4305: Gebruiksaanwijzing (20 pagina's)
Pagina afdrukken
21. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
22. Use the power tool, accessories and tool bits
etc. in accordance with these instructions and in
the manner intended for the particular type of
power tool, taking into account the working con-
ditions and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
Service
23. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
24. Follow instruction for lubricating and changing
accessories.
25. Keep handles dry, clean and free from oil and
grease.
SPECIFIC SAFETY RULES
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to jig saw safety rules. If you use this tool unsafely or
incorrectly, you can suffer serious personal injury.
1.
Hold power tools by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed metal
parts of the tool "live" and shock the operator.
2.
Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body
leaves it unstable and may lead to loss of control.
3.
Always use safety glasses or goggles. Ordinary
eye or sun glasses are NOT safety glasses.
4.
Avoid cutting nails. Inspect workpiece for any
nails and remove them before operation.
5.
Do not cut oversize workpiece.
Selecting the cutting action (Fig. 3)
This tool can be operated with an orbital or a straight line cutting action. To change the cutting action, just turn the lever
to the desired cutting action position. Refer to the table below to select the cutting action.
Position
0
Straight line cutting action
I
Small orbit cutting action
II
Medium orbit cutting action
III
Large orbit cutting action
Switching ON and OFF
For 4304 (Fig. 4)
CAUTION:
Before plugging in the tool, always check to see that the
switch trigger actuates properly and returns to the "OFF"
position when released.
To switch on, press the trigger. To switch off, release the
trigger.
Cutting action
6.
Check for the proper clearance beyond the work-
piece before cutting so that the blade will not
strike the floor, workbench, etc.
7.
Hold the tool firmly.
8.
Make sure the blade is not contacting the work-
piece before the switch is turned on.
9.
Keep hands away from moving parts.
10. Do not leave the tool running. Operate the tool
only when hand-held.
11. Always switch off and wait for the blade to come
to a complete stop before removing the blade
from the workpiece.
12. Do not touch the blade or the workpiece immedi-
ately after operation; they may be extremely hot
and could burn your skin.
13. Do not operate the tool at no-load unnecessarily.
14. Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
15. Always use the correct dust mask/respirator for
the material and application you are working
GEB016-1
with.
SAVE THESE INSTRUCTIONS.
WARNING:
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.
OPERATING INSTRUCTIONS
Installing or removing the saw blade (Fig. 1 & 2)
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the blade.
To install the blade, loosen the screw on the blade holder.
With the blade teeth facing forward, insert the blade into
the blade holder as far as it will go. Make sure that the
back edge of the blade fits into the roller. Then tighten
the screw to secure the blade.
NOTE:
Occasionally lubricate the roller.
For cutting mild steel, stainless steel and plastics.
For clean cuts in wood and plywood.
For cutting mild steel, aluminum and hard wood.
For cutting wood and plywood.
For fast cutting in aluminum and mild steel.
For fast cutting in wood and plywood.
For 4305 (Fig. 5)
CAUTION:
Before plugging in the tool, always check to see that the
switch actuates properly.
To switch on, slide the switch lever forward. To switch off,
slide the switch lever backward.
7
Applications