ALIBI ALI-TS4002R Snelle installatiehandleiding - Pagina 2
Blader online of download pdf Snelle installatiehandleiding voor {categorie_naam} ALIBI ALI-TS4002R. ALIBI ALI-TS4002R 5 pagina's. 2 mp 4-in1 hd 130 ft ir bullet camera
Pagina afdrukken
d.
Connect the camera drop cable to video and power extension cables as required.
e.
Connect the other end of the video extension cable to a compatible recorder.
Drop cable connectors are not waterproof. Seal if needed.
NOTE
f.
Connect the other end of the power extension cable to a 12 Vdc (observe polarity - see page
1) or 24 Vac power source.
g.
Verify that video from the camera can be seen on your recorder or monitor.
h.
Use the drop cable Switch button to select the video format you prefer. The tag on the drop
cable describes how to select video formats. Usually the video format of the camera is shown
on default live view screen of the recorder.
i.
Route the drop cable through the hole in the mounting surface, or through the cable channel
in the mounting base, then attach the camera assembly to the surface using the appropriate
fasteners.
Mounting the camera with a junction box
•
The ALI-AJ1 junction box is shown below. It can be attached to a wall or ceiling. Video and power
extension cables can be routed in through the opening in the back of the box or through the conduit
coupling, and attached to the camera drop cables inside the enclosure.
To use the junction box:
a.
Remove the ALI-AJ1 front plate from the box by removing the three screws (see above).
b.
Attach the front plate to the camera mounting base using three screws. If the box will be
wall attached to a wall, ensure that the "UP" label on the mounting plate is at the top of the
camera, and the cable channel in the camera mounting base is toward the bottom of the
camera.
c.
Using the ALI-AJ1 box as a guide, mark and then drill three holes for the screws that will
attach the box to the wall or ceiling. If the extension cables will be routed into the box
through the mounting surface, also drill a hole for the extension cables.
d.
Attach the box to a wall or ceiling with three screws. Ensure that the wall or ceiling will
support at least three times the weight of the camera with the junction box.
e.
Route the video and power extension cables into the box.
f.
Attach the video and power extension cable to the camera drop cables. If powering the
camera with 12 Vdc, observe the polarity of the power cable connector as shown on page 1
of this guide.
g.
Verify that video from the camera can be seen on your recorder or monitor.
h.
Use the drop cable Switch button to select the video format you prefer. The tag on the drop
cable describes how to select video formats. Usually the video format of the camera is shown
on default live view screen of the recorder.
i.
Reattach the ALI-AJ1 front plate (with the camera) to the box.
2
www.observint.com
Holes for
mounting
base
screws (6)
Front
plate
Box
Conduit
Front
coupling/
cable
channel
Camera adjustments
1.
While observing video from the camera, loosen the pan and tilt lock screws, point the camera at
your surveillance target, and then tighten the screws to hold the camera in position.
Pan lock
screw
Tilt lock
screw
Tilt:
0° ~ 90°
Pan: 0° ~ 360°
Mounting bracket adjustment
2.
If a rotation adjustment is needed, loosen the rotation lock screw and adjust the camera to adjust
the horizontal alignment of the camera video.
Open the OSD menu through the recorder
You can open the OSD menu through the recorder in either of two ways: 1) using the recorder main console,
and 2) by logging into the recorder remotely.
Opening the OSD Menu through the recorder console
•
To open the OSD menu on the recorder monitor:
a.
Open the recorder Live View screen, and then click inside the screen where the PTZ camera
video image is displayed. See below.
b.
Click the PTZ Control icon in the Quick Setting Toolbar. The PTZ camera Live View window
will expand to full screen and the pop-up window shown below will open.
Menu icon
c.
In the PTZ Control panel pop-up window, click the Menu icon on the Configuration line.
Rotation lock screw
0° ~ 360°
© 2019 Observint Technologies. All rights reserved.