Makita 6704DW Gebruiksaanwijzing - Pagina 6

Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Makita 6704DW. Makita 6704DW 8 pagina's. Cordless angle socket driver

Pagina afdrukken

OPERATING INSTRUCTIONS

Installing or removing battery cartridge

(Fig. 1)

• Always switch off the machine before insertion or

removal of the battery cartridge.

• To remove the battery cartridge, pull out the set

plate on the machine and grasp both sides of the

cartridge while withdrawing it from the machine.

• To insert the battery cartridge, align the tongue on

the battery cartridge with the groove in the housing

and slip it into place. Snap the set plate back into

place. Be sure to close the set plate fully before

using the machine.

• Do not use force when inserting the battery car-

tridge. If the cartridge does not slide in easily, it is

not being inserted correctly.

Charging (Fig. 2)

1. Plug the battery charger into your power source.

2. Insert the battery cartridge so that the plus and

minus terminals on the battery cartridge are on the

same sides as their respective markings on the

battery charger. Insert the cartridge fully into the

port so that it rests on the charger port floor.

3. When the battery cartridge is inserted, the charg-

ing light color will flash in red color and charging

will begin.

4. When charging is completed, the charging light

goes out. The charging time is as follows:

Battery 9100 and 9100A: approx. 60 minutes.

5. If you leave the battery cartridge in the charger

after the charging cycle is complete, the charger

will switch into its ''trickle charge (maintenance

charge)'' mode.

6. After charging, remove the battery cartridge from

the charger and unplug the charger from the

power source.

Capacity

Battery type

9100

CAUTION:

• The battery charger is for charging Makita battery

cartridge. Never use it for other purposes or for

other manufacturer's batteries.

• When you charge a new battery cartridge or a

battery cartridge which has not been used for a long

period of time, it may not accept a full charge. This

is a normal condition and does not indicate a

problem. You can recharge the battery cartridge

fully after discharging it completely and recharging a

couple of times.

• When you charge a battery cartridge from a just-

operated machine or a battery cartridge which has

been left in a location exposed to direct sunlight or

heat for a long time, let it cool off. Then re-insert it

and try to charge it once more.

Number of

(mAh)

cells

1,300

• When you charge a new battery cartridge or a

battery cartridge which has not been used for a long

period, sometimes the charging light will go out

soon. If this occurs, remove the battery cartridge

and re-insert it. If the charging light goes out within

one minute even after repeating this procedure a

couple of times, the battery cartridge is dead.

Replace it with a new one.

Trickle charge (Maintenance charge)

If you leave the battery cartridge in the charger to

prevent spontaneous discharging after full charge,

the charger will switch into its ''trickle charge (main-

tenance charge)'' mode and keep the battery car-

tridge fresh and fully charged.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely

discharged.

Always stop machine operation and charge the

battery cartridge when you notice less machine

power.

2. Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room tempera-

ture at 10°C – 40°C (50°F – 104°F).

Let a hot battery cartridge cool down before

charging it.

Installing or removing socket

Important:

Always be sure that the machine is switched off and

the battery cartridge is removed before installing or

removing the socket.

For machine with square drive (Fig. 3 & 4)

Use 9.5 mm square drive socket with a hole for detent

pin which is available on the market. (Note: Use

6.35 mm square drive socket when using the machine

with 6.35 mm square drive.)

To install the socket, depress the detent pin on the

square drive with your finger and push the socket onto

the square drive until the detent pin is inserted into the

hole in the socket.

To remove the socket, depress the detent pin with a

small hand tool and pull off the socket.

For machine with round drive (Fig. 5)

Use a bit with Form C 6.3 shank which is available on

the market. The bit can be inserted directly into the

round drive and held in place.

To install the bit, push it firmly into the round drive.

To remove the bit, grasp it with a pair of pliers and pull

it out of the round drive. Sometimes, it helps to wiggle

the bit with the pliers as you pull.

Switch action (Fig. 6)

CAUTION:

Before inserting the battery cartridge into the

machine, always check to see that the switch trigger

actuates properly and returns to the ''OFF'' position

when released.

To start the machine, simply pull the trigger. Release

the trigger to stop.