KitchenAid 9750520 Installatie-instructies - Pagina 3

Blader online of download pdf Installatie-instructies voor {categorie_naam} KitchenAid 9750520. KitchenAid 9750520 5 pagina's. 30" electric freestanding range

Pagina afdrukken

centerline

3-wire electrical connection

See Panel C for 4-wire electrical connection.

IF CONNECTING

TO A 4-WIRE

ELECTRICAL

SYSTEM: This aooliance

is manufactured

with ground connected ii

cabinet. The ground

must be revised so the

green grounding wire of the 4-wire power cord is

connected to the cabinet. See 4-wire electrical

connection section, Panel C.

When a 4-wire receptacle of NEMA type 14-50R

is used (See Figure 2), a matching U.L.-listed, 4-

wire, 250-volt, 40-ampere, range power supply

cord (pigtail) must be used. This cord contains

four copper conductors with ring terminals on the

appliance end, terminating in a NEMA Type 14-

50P plug on the supply end. The fourth

(grounding) conductor must be identified by a

green or green/yellow

cover and the neutral

conductor by a white cover. Cord should be Type

SRD or SRDT with a U.L.-listed strain relief and

be at least four feet long.

The MINIMUM conductor sizes for the copper 4-

wire power cord are:

7 I

40 ampere circuit

2, No.-8 conductors

1, No.-1 0 white neutral

1, No.-8 green grounding

Conduit

connector

Knock-out

opening

for 40.amDere

Dower

opening

,='c

(12(

. To mount anti-tip

bracket to wood

or metal wall stud: Find the wall stud

that is closest to the center of the range location.

(Note: Wall stud should Not be more than 12

inches to the right or left of center of range

location.) Measure and mark at the center of the

wail stud a distance of 44 inches up from the

floor.

To mount anti-tip

bracket to concrete

concrete

block wall: Measure and mark on the

rear wall at the center of the range location a

distance 44 inches up from the floor. (Note: Anti-

tip bracket can Not be installed more than 12

inches to the right or left of center of range

location.)

U.L. listed

conduit

connector

If appliance

is to be connected

directly

fused disconnect

or circuit

breaker b&x:

Assemble a U.L.-listed conduit connector in the

conduit connector opening provided. Insert the

power supply cable through the conduit connector,

allowing enough slack to easily attach the wiring to

the terminal block.

If a U.L.-listed,

40.ampere

range power supply

cord (pigtail)

is used: Remove the knockout for

the 40.ampere power supply cord.

Assemble a U.L.-listed strain relief in the hole.

Insert the power supply cord through the strain

relief, allowing enough slack to easily attach the

wiring to the terminal block.

Do not loosen the factory installed nuts already

installed on the terminal block.

Use only ring-type

terminals

to connect

the

power supply.

To secure the power supply

cord, use the 3/8" brass nuts taped to cabinet

below the terminal

block.

Be sure the wiring

nuts are installed

tight.

The wiring diagram is also located on

the back of the range.

Electrical

Shock Hazard

Take special care when drilling

holes into

the wall. Electrical

wires may be

concealed

behind the wall covering.

Locate the electrical

circuits

that could be

affected by the installation

of this bracket

and turn off the power to these circuits.

Failure to follow these instructions

may

result in electrical

shock or other

personal

injury.

3-wire wall

4-wlre wall

receplacle

receptacle

(lo-50R)

(14~50R)

Figure

Now start...

With range in kitchen.

Property

Damage

Contact a qualified

installer

for the best

procedure

to drill mounting

holes through

the type of wall covering

(i.e. ceramic tile)

and into wall stud, concrete

or concrete

block wall.

Before moving

range across floor, check

that range is on shipping

base or slide

range onto cardboard

or hardboard.

Failure to follow these instructions

may

result in damage to wall or floor covering.

Remove racks and other parts

from inside oven.

Take 4 cardboard corners from the

carton. Stack one cardboard corner on

top of another. Repeat with other two corners.

Place corners lengthwise on the floor in back of

range.

1131

. Line up

the "TOP"

This appliance

is manufactured

with the

neutral terminal

connected

to the cabinet.

local codes Do Not permit grounding

through

the neutral, a four-wire

power supply

cord

rated 250.volts,

40.amperes

and investigated

for use with ranges must be used. See 4-wire

electrical

connection,

Panel C.

BEI

, Connect the neutral (white) wore to the

silver-colored

terminal screw on the

terminal block. Connect the other two wires to the

outer terminal screws on the terminal block. Use

ring-type terminals only. Connect with the brass nuts

attached to the range. Do Not loosen factory-

installed nuts already on the terminal. Check that

nuts are tight to insure proper electrical connection.

Tighten the strain relief clamping

screws or the locking ring and clamping

screws of the conduit connector. Replace terminal

block cover.

P-J

Firmly grasp the range and gently lay it

on its back on the cardboard corners.

mounting hole on

4b"

anti-tip bracket with

-~-

'I)r

mark on wall. Use a

pencil to mark the

location of the top

and bottom mounting holes. Remove bracket. if

wail covering

is ceramic tile, drill a 3/l 6-inch

hole through tile only. Then proceed as follows:

For wood or metal wail studs:

Drill l/8" holes at each mounting hole location

through wall and into stud.

For concrete

or concrete

block wall:

Drill 3/l 6" holes (l -3/4-inch minimum deep) at

each mounting hole location. Tap plastic anchors

into mounting holes with hammer.

141

Pull cardboard shipping base firmly

to remove.

Use adiustable wrench

to loo&

leveling legs four complete turns.

Place cardboard or hardboard in front

of range. Stand range back up.

on bracket with

holes on wall,

making sure that

the "TOP"

mounting hole on '

bracket is lined up

with top hole in wall. Securely fasten bracket to

wall using screws provided.

Remove the shipping materials including

tape and protective film from range.

,I,

fermlnal

nuts

To prevent tipping,

install range anti-tip

bracket.

Anti-tip

bracket must be attached

to a

wood or metal wail stud, or concrete

concrete

block wall.

Do Not attach anti-tip

bracket to a cabinet.

Save these Installation

Instructions.

range is moved to a new location,

the

anti-tip

bracket must be removed

and

reinstalled

in the new location.

Plug range power supply cord into

arounded outlet. Carefully slide ranae

into position until range is approximately

2 incGes

from rear wall. Remove shipping base, cardboard

or hardboard from under the range.

181

Remove the terminal block cover located

on the back of range.

Panel B