ALIBI ALI-NS2024R Snelle installatiehandleiding - Pagina 2
Blader online of download pdf Snelle installatiehandleiding voor {categorie_naam} ALIBI ALI-NS2024R. ALIBI ALI-NS2024R 6 pagina's. 4mp ip low light turret camera
![ALIBI ALI-NS2024R Snelle installatiehandleiding](/uploads/products/server2/210435/210435.jpg)
c.
Place the enclosure over the
turret module.
d.
While feeding the drop cable
through the cable channel
or through the hole of the
mounting surface, reposition
the enclosure with the turret
onto the base, then secure it
with lock screw. Do not tighten
the screw at this time.
12.
pply power to the camera.
A
Step 2.
Install the Alibi Config Tool software
NOTE: If the camera LAN extension cable is attached to a Network Video Recorder (NVR), skip this step.
The Alibi Config Tool is a PC-based network utility for discovery of Alibi compatible devices. It provides
an easy way to activate devices, configure camera and recorder network configuration settings, and set
device passwords. It can be installed on a Microsoft® Windows® operating system that has direct access
to the network where your Alibi devices are installed. You can download the Alibi Configuration Tool from
Supercircuits.com or AlibiSecurity.com/Resources.
Download the Alibi Config Tool from the Supercircuits.com or AlibiSecurity.com/Resources
1.
website. At the time when this document was published, the file is named: alibi-config-tool.zip
and is about 80MB.
2.
Un-zip the file on a computer with Microsoft Windows (Windows 7 or newer) that is connected to
the LAN where your Alibi camera is connected.
3.
Run the file contained in the zip file: Alibi Config Tool.exe. Follow the on-screen instructions to
install the file.
4.
Open the Alibi Config Tool application. When the application opens, it automatically "discovers" and
lists all Alibi compatible devices on the LAN. See below.
Notice: In the screen above, the tool discovered devices with IP addresses of 192.168.0.xxx and
192.168.3.xxx. It will also list other Alibi compatible devices on the LAN, and devices with the
address 192.168.1.64 (an inactive Alibi device).
Step 3.
Activate Inactive Alibi device
NOTE: If the camera LAN extension cable is attached to a Network Video Recorder (NVR), skip this step.
Refer to the documentation available for your NVR firmware for the procedure to activate the camera, if
necessary.
When an Alibi device is first installed, or reset to its factory configuration, it must be "Activated" before it
can be used. In the Alibi Configuration Tool, "Inactive" devices have a Security status of Inactive, and
an IPv4 address of 192.168.1.64. A device is "Activated" when a password is assigned to the admin
username of the device.
In the example below, an ALI-NS2024VR camera is activated and configured for its network. The procedure
is similar for all other Alibi network cameras currently available.
www.observint.com
2
1.
Scan through the list of devices the Alibi Config Tool discovered for the Inactive device you want to
activate (see below). Click on the device in the list to highlight it, and then click the select box to
check it. See below.
Activate
2.
Click the Activate button. In the Activate window, you will create a password for the admin
(administrator) username.
a.
In the Activate window, enter an a password for admin in the New Password field. Include a
combination of uppercase, lowercase alphabetic characters and numbers to create a "Strong"
password. The rating is shown beneath the field. See above.
b.
Enter the admin password again in the Confirm field, and then click Activate. In the
screen below, notice that the device Security status shows "Active". Record your admin
password for reference later.
If you lose your admin (administrator) password, you cannot configure the device or restore
it to its factory settings. To reset your password, call your support organization for specific
CAUTION
instructions.
Notice that although the device is now activated, it retained the default IP address.
Step 4.
Modify Network Parameters
NOTE: If the camera LAN extension cable is attached to a Network Video Recorder (NVR), skip this step.
The camera will receive network configuration settings from the NVR. Refer to the documentation available
for your NVR firmware for more information.
You can change the network parameters of devices that are active.
1.
In the list of devices discovered, click on the device you want to change the network settings for, and
then click the select box to check it. See below.
© 2018 Observint Technologies. All rights reserved.