Lexmark 08A0332 - E322N 16PPM LASERPR 16MB-1200IQ USB FETH 220V Snelle referentie
Blader online of download pdf Snelle referentie voor {categorie_naam} Lexmark 08A0332 - E322N 16PPM LASERPR 16MB-1200IQ USB FETH 220V. Lexmark 08A0332 - E322N 16PPM LASERPR 16MB-1200IQ USB FETH 220V 2 pagina's. Lexmark e320: quick reference
Pagina afdrukken
Lexmark™ E320/E322
Quick Reference
Loading tray 1
1
Extend the rear paper support until you
hear a click.
2
Flex the sheets back and forth to loosen
them, then fan them. Straighten the
edges on a level surface.
Note:
Not flexing and fanning the paper may
cause paper feed problems and jams.
3
Load:
•
letterhead paper with the top of the
page pointing down, facing you.
•
envelopes in the center of the tray.
Load them vertically, flap side down,
with the stamp area in the top left
corner.
4
Extend the front paper support on the
paper output bin.
5
Slide the paper guides flush against the
edges of the media.
6
Open the front output door if you're
printing on special media.
7
Choose the paper size and type from
your software application.
8
Start your print job.
Loading the optional
tray 2
Grasp the tabs on either side of the tray and
pull it completely out of the printer.
1
If loading:
•
letterhead paper, insert letterhead
face down with the top of the page
entering the printer first.
•
A4 or legal size paper, extend the
paper support.
2
Make sure the metal plate is pressed
down before inserting it into the printer.
Note:
After the tray is inserted, the metal plate
springs back up so the paper can feed
into the printer.
3
Do not exceed the stack height indicator;
overfilling the tray may cause jams.
4
Slide the paper guides against the edges
of the paper.
5
Make sure the paper is under both
corner bucklers and is flat in the tray.
Stack height
Corner
indicator
bucklers
6
Reinstall the tray, making sure the tray is
pushed all the way in.
7
Select the paper size and type from your
software application.
8
Start your print job.
Clearing jams
The Paper Jam light prompts you to clear the
paper path.
1
Open the printer cover.
2
Remove the print cartridge (it may be
warm) and cover it.
Note:
Exposing the photoconductor to light
may damage the print cartridge.
Photoconductor
3
Gently pull out the media.
Fuser
Roller
Caution!
The fuser may be hot!
4
If the media is jammed tightly behind the
roller, or if you can't get a grip on it, close
the cover, open the front output door,
and pull out the paper.
5
Make sure there is no more media in the
printer.
6
Reinstall the print cartridge.
7
Close the printer cover to resume
printing.
If the jam occurs as it exits tray 2 into the
printer:
1
Open the printer cover.
2
Remove the print cartridge (the print
cartridge may be warm).
3
Gently pull the paper toward you.
4
Reinstall the print cartridge.
5
Close the printer cover to resume
printing.
If you cannot reach the paper easily:
1
Turn off the printer. (You will lose the rest
of the print job.)
2
Lift the printer off the 250-sheet drawer.
3
Remove the paper.
4
Reinstall the drawer.
5
Turn on the printer.
6
Resend your print job.
If the jam occurs just after the paper feeds
from tray 2:
1
Pull the tray all the way out.
2
Gently pull the paper toward you.
3
Reinstall the tray to resume printing.