KitchenAid KEBC147KBL0 Installatie-instructies - Pagina 3
Blader online of download pdf Installatie-instructies voor {categorie_naam} KitchenAid KEBC147KBL0. KitchenAid KEBC147KBL0 5 pagina's. 24" electric built-in single and double ovens
Pagina afdrukken_fcodes p ermit a ndaseparate g rounding w ireis
used, i t is recommended
thataqualified
e_ectrician
determine
that the grounding
path and wire gauge
are in accordance
with toca_ codes.
Do Not ground to a gas pipe.
Check with
a qualified
electrician
if you are not
sure oven is proper_y grounded.
Do Not have a fuse in the neutral
or grounding
circuit.
Oven must be connected to the proper eUectdcaU
voUtageand frequency as specified on the
modeU/sedd rating plate. (The model/serial rating
plate is located on the oven door or on the oven
frame.}
[_ Models rated from 7.3 to 9.6 kW at 240 volts
(5.5 to 7.2 kW at 208 volts) require a separate
@-ampere circuit. Models rated at 7.2 kW and
below at 240 volts (5.4 kW and below at 208
volts) require a separate 30-ampere circuit.
[_ A time-delay fuse or circuit breaker is
recommended.
[_ Connect directly to the fused disconnect (or
circuit breaker box} through flexible, armored
or non-metallic sheathed, copper cable (with
grounding wire}.
[_ Flexible armored cable from appliance should
be connected directly to junction box.
[_ Fuse both sides of the line.
[_ A U.L.qisted conduit connector must be
provided at the junction box.
[_ Do Not cut the conduit.
Wire sizes and connections must conform with the
rating of the appliance and to the requirements of
the National Electrical Code, ANSI/NFPA 70 -- latest
edition (% See Page 1) and all local codes and
ordinances.
if the house has aluminum wiring, follow the
procedure below.
a.} Connect the aluminum wiring to the copper wire
using special connectors designed and
Underwriters Laboratories-listed for joining
copper to aluminum. Follow the electrical
connector manufacturer's recommended
procedure.
b.} Aluminum/copper
connection must conform
with local codes and industry-accepted wiring
practice.
Grasp
oven
frame to li_
oven.
(
Use screws to attach
oven to cabinet.
Grasp
oven
Reattach
side
frame to lift
trim.
oven.
Remove
trim screws.
Remove
side
trim.
Use screws to
attach
oven to
cabinet.
Preparation
Excessive
Weight Hazard
Use two or more people to move and
install oven.
Failure to follow this instruction can
result in back or other injury.
Important: Use both hands to remove oven
doors.
Do Not use handb or any portion of the front
frame or trim for lifting.
Before moving oven across floor, check that oven
is on shipping base or slide oven onto cardboard
or hardboard.
Do Not remove shipping feet at the front tower
corners of oven.
Remove
oven
door.
Remove trim
screws.
match on the
hinge
in mocked position
=
door
free
to open
and close
latch
on the
hinge
position
= door
ready
for removal
shipping
feet.
Turn power supply off. Move oven close to
final position.
Remove and discard shipping
materials,
tape
and protective
film from the oven.
Do Not
remove shipping
base or shipping
feet at the
front bwer
corners of oven.
The shipping
feet
will protect the Jower oven trim unti_ oven is
inserted
into cabinet.
, Remove and set aside racks and other parts
from inside oven.
m Completely open oven door. In both back
corners of the door you will see door latches in the
locked position. Rotate both latches forward to the
unlocked position.
Grasp outside edges of door with both hands.
• Begin closing door, atthe moment the door
stops closing, lift and puii door toward you.
, Set door aside on a protective surface.
Pull top of trim
down,
3m
Remove trim screws attaching right and
left side trim to oven. Grasp the bottom end of
trim and pull away from oven. Slide top end of
trim downward to remove trim from oven. Take
care not to scratch other surfaces with ends of
trim. Set trim and screws aside on protected
surface.
Page 2