Jandy CL Series Installatie- en bedieningshandleiding - Pagina 10

Blader online of download pdf Installatie- en bedieningshandleiding voor {categorie_naam} Jandy CL Series. Jandy CL Series 16 pagina's. Cartridge pool filters

Pagina afdrukken
Page 10
10. Using new cartridges or the clean original ones,
place the cartridges back into the fi lter tank. Be
sure that they are correctly seated on the cartridge
support on the bottom of the tank.
11. Inspect the o-ring at the top of the outlet tube for
cracks and wear marks. Replace if necessary.
12. Reinstall the manifold making sure that it fi ts
squarely over the cartridges and outlet tube.
13. Inspect the tank o-ring for cracks or wear marks.
Replace if necessary. Place the o-ring back onto
the fi lter bottom.
14. Place the fi lter lid onto the fi lter tank bottom.
15. Replace the tank clamp ring. See Section 3.4 for
clamp installation.
16. Start the pump by following the procedures
outlined in steps 2 through 7 of Section 4.1.

Section 6. Maintenance

6.1 General Maintenance

1.
Wash outside of fi lter with a mild detergent and
water. Rinse off with a hose. Do not use solvents
to clean the fi lter, solvents will damage the plastic
components of the fi lter.
2.
Check pressure during operation at least once a
week.
3.
Remove any debris from the skimmer basket and
hair/lint pot on pump.
4.
Check pump and fi lter for any leaks. If any leaks
develop, turn off the pump and call a qualifi ed
pool service technician.
5.
Product safety signs or labels should be
periodically inspected and cleaned by the product
user as necessary to maintain good legibility for
safe viewing distance.
6.
Product safety signs or labels should be replaced
by the product user when a person with normal
vision, including corrected vision, is no longer
able to read the safety signs or label message panel
text at a safe viewing distance from the hazard.
In cases where the product has an extensive
expected life or is exposed to extreme conditions,
the product user should contact either the product
manufacturer or some other source to determine
means for obtaining replacement signs or labels.
7.
Installation of new replacement safety signs or
labels should be in accordance with the sign or
label manufacturer's recommended procedure.

6.2 Pressure Gauge

Caution
Maintain your pressure gauge in good working order.
The pressure gauge is the primary indicator of how
the fi lter is operating.
1.
During operation of the fi ltration system, check
the pressure gauge/air release assembly for air or
water leaks at least once a week.
2.
Keep the pressure gauge in good working order.
If you suspect a problem with the gauge, Jandy
recommends you call a qualifi ed service technician
to do any work on the fi lter/pump system.

6.3 Cleaning the Filter Cartridge

1.
Follow the procedures outlined in steps 1 through
8 of Section 5.1 to expose the cartridge elements
inside the fi lter.
2.
Remove cartridge elements and place them upright
in an area suitable for washing.
3.
Use a garden hose and nozzle to wash each pleat
of each element.
NOTE
Algae, suntan oil, calcium and body oils can form
coatings on fi lter element which may not be removed
by normal hosing. To remove such materials, soak
the element in de-greaser and then a de-scaler. Your
local pool dealer will be able to recommend suitable
products.
4.
Inspect each cartridge for holes, tears or
excessively worn pleats. Replace if necessary.
5.
To reassemble the fi lter with the new or clean
cartridges follow the procedure outlined in steps
10 through 16 of Section 5.

Section 7. Winterizing

1.
Turn off the pump and circuit breakers.
2.
Open air release valve on top of the fi lter.
3.
Remove the drain plug at the base of the fi lter to
ensure that the tank is empty. Store the drain plug
and seal in a safe place. Do not reinstall until next
season at start-up.
4.
Drain system piping of all water.
5.
Cover the system with a tarpaulin or plastic sheet
to protect it from the weather.