Gardena HE 36 4000 Gebruiksaanwijzing - Pagina 7

Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Gardena HE 36 4000. Gardena HE 36 4000 14 pagina's.

Pagina afdrukken

You can order these spare parts

washers (17) are fitted under

from your GARDENA dealer

the nuts (16) and that the nuts

or directly from the GARDENA

(16) are on top of the blade

customer service.

bar (20).

Never use spare parts or ac-

7.3 Replacing the blade bar

cessories which have not been

Damaged blade bars must be

replaced to prevent imbalance.

7.2 How to replace the

blades

For safety reasons the blade

(ill. G / O)

bar must be replaced by

GARDENA service centres

Note: The blades have two

or dealers authorised by

cutting edges.

GARDENA.

If one edge has become blunt

the blade can be reversed.

7.4 Replacing the aerator

Broken blades must be re-

cylinder (ill. H / P)

placed immediately due to

The aerator cylinder is subject

potential imbalance.

to natural wear and tear. If the

springs (21) are worn the unit

Do not regrind the blades due

will not aerate efficiently. The

to potential imbalance.

springs and / or the aerator cylin-

The blades must always be re-

der must be replaced.

placed or reversed in pairs.

Hattrick HE 32 ( ill. P)

When replacing the blades (18)

1. Disconnect from the mains

always use new nuts and bolts

supply !

supplied with the spare blades.

2. Upturn the Hattrick onto the

right-hand side of the mower

1. Remove the mains plug.

housing.

2. Loosen both locking nuts

3. Use a suitable crosstip scr-

(16) while holding the corre-

ewdriver to loosen the screws

sponding screws (19). Use

(31).

the TORX

-wrench provided.

4. Remove the plastic support

3. Reverse the blades or mount

bracket (32).

new blades and secure tightly

5. Take out the aerator cylinder

(torque 25 Nm).

(33) by tilting and removing

Tip: During installation make

from the drive shaft (34)

sure that the toothed locking

(triangular driver).

7.6 Storage

HE 32

HE 36 / HE 40

Always store your electric Hattric lawn mower in a closed room.

For the Hattrick HE 32 the guide

To save space the handle of the Hattrick HE 36 / HE 40 can be folded

handle and the lower part of the

down Z-shaped. For this, loosen the lower linkage locking handles (2)

frame can be detached.

and pull the bars sideways out of the mount. Loosen the bar tightening

handle (1) at the joint and fold the upper part of the handle backwards

(ill. A).

When folding down the bars make sure that the connection

cable is not jammed or damaged.

If you have any problem with

Service, or return the defective

your electric Hattrick lawn mower,

unit together with a short descrip-

please contact our Customer

tion of the problem and, in case

of guarantee, with a copy of the

6. Fit a new aerator cylinder (33)

to the drive shaft (34) (trian-

gular driver), mount the plastic

support bracket (32) and screw

down with both screws (31).

Hattrick HE 36 / HE 40 ( ill. H)

1. Disconnect from the mains

supply !

2. Upturn the Hattrick onto the

left-hand side of the mower.

3. Use a suitable crosstip screw-

driver to loosen the screws

(26).

4. Remove the bearing plate (27).

5. Take out the aerator cylinder

(28) together with the end plate

(29) by removing both from the

drive shaft (30) (rectangular).

6. Fit a new aerator cylinder (28)

to the drive shaft (30) (rectan-

gular), mount the end plate (29)

and fasten down in the Hattrick

housing together with the bea-

ring plate using both screws

(26).

7.5 Service

Residual dirt and grass is easily

removed immediately after mow-

ing. For this, place the electric

Hattrick lawn mower on its side

and clean it with a brush or rag.

Also remove residue from the

aerator cylinder.

receipt to one of the GARDENA

service centres listed on the rear

page.

We expressly point out that,

in case of repair or exchange,

according to the product liabili-

other than original GARDENA

ty law, we are not liable for any

parts are used and repair is not

damage caused by our units if,

carried out by a GARDENA

8. Trouble-shooting

The following table contains the

For any other problem please

problems most frequently occur-

contact for safety reasons

ring and shows how to remedy

one of the GARDENA service

them.

Problem

Possible cause

Abnormal noise.

Motor fixing screws or

Clattering in the unit.

mower casing loose.

Whistling noise.

Foreign body blocking

aerator cylinder.

V-belt slipping.

Uneven running.

Blade bar or blades damaged

Strong vibration of the unit.

(imbalance).

Blade bar fastening on motor

shaft is loose.

Motor does not start.

Defective cable.

Cable cross section possibly

too small.

Motor cuts out.

Blocking by foreign matter.

Overload protection has

responded.

Cutting height is set too low.

Overload protection has

responded.

Aerator cylinder does not run.

Rotary switch is in position »0«.

V-belt defective.

Lawn turns to yellow.

Blades are too blunt.

Not a clean cut.

Cutting height is set too low.

service centre or an authorised

specialist. The same also ap-

plies to spare parts and acces-

sories.

centres or an authorised

specialist.

Remedy

Tighten screws.

Switch off aerator cylinder,

disconnect mains plug, remove

foreign body.

Contact GARDENA Service

Centre.

Tighten the blade or blade bar

screws.

Contact GARDENA Service

Centre.

Check power supply cable.

Use cable with a cross section

of at least 1.5 mm

Switch off motor. Remove mains

plug. Remove foreign matter.

Let motor cool down for about

2 or 3 minutes and start your

electric Hattrick lawn mower

again.

Make a first cut with the aerator

cylinder switched off and

a greater cutting height set.

Set rotary switch to position »I«.

Replace V-belt. Contact

GARDENA Service Station.

Replace or reverse the blades.

Correct cutting height.