Gardena Comfort 5000/5 Gebruiksaanwijzing - Pagina 3
Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Gardena Comfort 5000/5. Gardena Comfort 5000/5 10 pagina's. Garden pump
Ook voor Gardena Comfort 5000/5: Gebruiksaanwijzing (17 pagina's), Gebruikershandleiding (14 pagina's), Gebruikershandleiding (12 pagina's), Gebruikershandleiding (10 pagina's), Gebruikershandleiding (10 pagina's), Gebruiksaanwijzing (13 pagina's), Gebruiksaanwijzing (17 pagina's)
Pagina afdrukken
3. Initial Operation
Setting up your Garden Pump:
The site must be firm and solid in order to ensure safe and sturdy
operating conditions for the pump.
v Position the pump at a safe distance (min. 2 m) from the liquid
to be pumped.
The pump must be installed in a location with low air humidity
and sufficient ventilation in the area of the ventilation slots.
It must be at a distance of at least 5 cm from the walls.
No dirtcontamination (e.g. sand or earth) may be sucked in
through theventilation slots.
Connecting hose to
Don't use any hose connection system fittings on the
suction side:
suction side! A vacuum-resistant suction hose must be used,
e. g. GARDENA Suction Unit, art. no. 1411.
2
In order to reduce the suction time, it is advisable to use a suction
hose with backflow preventer avoiding automatic draining of the
suction hose when the pump is stopped.
1. Screw a vacuum-resistant suction hose
1
connector on the suction side of the pump
2. For suction heights exceeding 4 m also secure the suction
hose
1
This relieves the pump of the weight of the suction hose.
Connecting hose to
The pumps have 2 connections
delivery side:
The pump connection not in use has to be closed by the cap
which can be unscrewed for connecting 2 hoses.
5
The pump connections
thread which can be used to connect 13 mm (1/2"), 16 mm (5/8")
or 19 mm (3/4") hoses via the GARDENA hose connection system.
Optimised use of the pump capacity is achieved by connecting
19 mm (3/4") hoses with e.g. GARDENA Pump Connection Set
3
Art. 1752, or by connecting 25 mm (1") hoses with GARDENA
z
4
Quick Thread Coupling with female thread Art. 7109 / Quick
Coupling Hose Connector Art. 7103.
v Connect the pressure hose
3
side
If more than 2 hoses / accessories are connected simultaneously,
we recommend using the GARDENA 2- or 4-Channel Water
Distributor Art. 8193/8194, GARDENA Twin-Tap Connector
Art. 940 which can be screwed directly onto the connection
on the delivery side
14
1
airtight onto the
2
.
(e.g. by fastening it to a wooden post).
3
ß
/
3a
on the delivery side.
3
/
ß
are equipped with a 33.3 mm (G 1")
3a
5
to the connector on the delivery
ß
/
.
3a
3
/
ß
.
3a
4. Operation
Filling the pump:
6
5
8
7
1
5
4
,
1
DANGER! Electric shock!
Risk of injury due to electric shock.
v Disconnect from the mains before filling the
Garden Pump.
ATTENTION!
v Before each operation, slowly fill the pump with liquid
to be pumped until it overflows (approx. 2 to 3 l).
6
1. Open the cap
on the filler neck
2. Fill the pump via the filler cap
7
approx. 2 to 3 l of the liquid to be pumped.
3. Tighten the cap
6
of the filler cap
4. Open any shut-off valves in the delivery line (accessories,
water stop, etc.).
5. Drain remaining water in pressure hose
escape during the suction process.
6. Switching on pump 4000/5: Lift and hold the delivery hose
at least 1 m vertically above the pump, press the On/Off
8
switch
(On/Off switch shines) and wait until the pump has
primed.
v If the pump does not deliver after approx. 5 minutes,
switch off the pump (press On/Off switch
(see 7. Trouble-Shooting).
min.
6. Switching on pump 5000/5; 6000/6 inox:
1 m
5
Lift and hold the delivery hose
1 m vertically above the pump, insert the
power plug, press the On/Off button
(the LED shines green) and wait until the
pump has primed.
z
If the pump does not deliver within
approx. 20 seconds, the LED flashes
orange.
If the pump does not deliver: 5000/5
within approx. 5 minutes / 6000/6 inox
within approx. 6 minutes, the LED
shines red and the pump switches off
automatically (see "7. Trouble-
Shooting").
v If the pump does not automatically
switch off then manually switch
the pump off and check the hose
for leaks.
The specified maximum self-priming suction height of 8 m is
reached only if the pump is filled via the filler neck
overflow and if, while doing so and during the self-priming, the
delivery hose
5
is held up sufficiently high to prevent any flow
medium escaping from the pump via the delivery hose
7
by hand.
to overflowing with
7
by hand (do not use pliers).
5
so that air can
5
8
)
LED
at least
ß
8a
7
up to the
5
.
15