KitchenAid KICU285HSS0 Installatie-instructies - Pagina 3
Blader online of download pdf Installatie-instructies voor {categorie_naam} KitchenAid KICU285HSS0. KitchenAid KICU285HSS0 4 pagina's. 48" island hood
Ook voor KitchenAid KICU285HSS0: Onderdelenlijst (4 pagina's)
Pagina afdrukken
Important: Observe allgoverning
codes andordinances.
It isthe customer's r esponsibility:
• Tocontact a qualified electrical
installer.
• To
assure
that
the
electrical
installation
is adequate
and
in
conformance
wlth
National
Electrical
Code,
ANSI/NFPA
70
--latest
edition
_ , or CSA
Standards
C22.1-94,
Canadian
Electrical
Code,
Part
1 and
C22.2
No.0-M91
- latest
edition**
and all local <:odes
and ordinances.
If codes
permit
and a separate
ground
wire
is used,
it is
recommended
that
a qualified
electrician
determine
that
the
ground
path
is adequate.
A 120-volt,
60 Hz, AC-only,
fused
eleGtrical
supply
is required
on a
separate
15-amp
circuit,
fused on
both
sides
of the line.
Do not ground
to a gas pipe.
Check
with
a qualified
electrician
if you are not sure range
hood
is
properly
grounded.
Do not have
a fuse
in the neutral
or ground
circuit.
IMPORTANT:
Save
Installation
Instructions
for
electrical
inspector's
use.
The range hood must be
connected w'Rh copper wire only.
The range hood should be
connected directly to the fused
disconnect (or circuit breaker) box
through flexible armored or
nonmetallic sheathed copper cable. A
U,L- or C.S.A.- listed strain relief must
be provided at each end of the power
supply
cable, Wire
sizes (COPPER
WIRE ONLY) and connections
must
conform
with the rating
of the
appliance
es specified
on the
model/serial
rating plate.
Wire sizes must conform
to the
requirements
of the National
Electrical
Coda ANSUNFPA 70 -- latest edition*,
or CSA Standards
C22.1-94,
Canadian
Electrical
Code Part 1 and C22.2 No.
0-M91 - latest edition H and all local
codes and ordinances.
A U.L.- or C.S.A,- listed conduit
connector
must be provided
at each
end of the power supply cable (at the
range hood and at the iuection
box).
Copiel; of the s_ndards
i_sted ntay be
Oblalned
from:
• Ngltlorl=l
Rill
Protection
Association
Elal_4_ryntarch
Park
e ulnmy,
M _sach
uset-_
02269
** Canmdlart
Standard
Association
178 RaXdale
BotlleVard
Etoblcoke
(Toronto),
Ontario
MSW
1R3
Preparation
Because of the size and weight of this
island canopy hood, the support sys-
tem must be securely attached to the
ceiling.
-- For plaster or sheet rock ceilings,
the support must be attached to
joists.
-- If this Is not possible, you must
build a support structure behind
the plaster or sheet rock.
Do Not cut a joist or stud unless
absolutely necessary. If a joist or stud
muat he cut, then a supporting frame
must be consl_ucted.
Before making cutouts, make sure
there Is proper clearance within the
ceiling or wall for exhaust vent.
= Put a thick, protective
covering
over countertop,
cooktop
or range to
protect from damage
or dirt. Select a
fiat surface for assembling
the unit.
Cover that surface with a protective
covering
and place all hood parts and
hardware
on it.
= Determine and mark the
centarline on the ceiling where the
range hood will be installed.
= Using the mounting
tamplata,
mark the location of the support
mounting bracket holes, vent cutout
(if used) and power supply cable
cutout on the ceiling. Use 1-1/4"
(3.2 cm) drill and saber saw or
keyhole saw to cut openings for
power supply cable and vent, (See
"Venting requirements" and
"Electrical requirements,"
Pages 3-5.
=
If venting IO the outside instaU
vent system. (See "Venting
requirements",
Page 3.) Use caulking
to seal exterior wall or roof openings.
== Run wiring through
ceiling
according to the National Electrical
Code or CSA Standards and local
codes and ordinances. There must be
enough power supply cable from the
fused disconnect {or circuit breaker)
box the to make the connections in
the hood's terminal box.
Do Not turn on power
until
installation
is completed,
Use caulking to seal ell openings,
Installation
screw
_s_c_r 6 w s
screw
.
Remove the four screws on the
upper chimney
and disassemble
chimney
pieces from support frame.